Question about Cars & Trucks

Open Question

Remove turn signal switch on 2007 impala - Cars & Trucks

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: how do i remove the turn signal switch on a 2001

Removal & Installataion

  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
  • Remove the upper and lower steering wheel trim covers using the following procedure.
    • Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
  • Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
  • Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
  • To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.

    Posted on Mar 06, 2010

    Ad
    • 4 Answers

    SOURCE: how to replace turn signal switch

    you will need to pull steering wheel you have a clock spring for the air bag behind it dangerous for a on trained technician simply put the air bag could kill you

    Posted on Mar 15, 2010

    • 409 Answers

    SOURCE: need to replace turn signal switch,2003 chev impala

    You only need to disconnect negative battery cable to make it safe to work on.

    Posted on Mar 18, 2010

    emissionwiz
    • 76118 Answers

    SOURCE: how to install turn signal switch 2007 chevy impala

    Watch the video, it is a different model but the columns are the same. Cick HERE

    Posted on Jun 15, 2012

    Testimonial: "Thank you so much for the instalation instructions. A great help."

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


    Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

    They are turned on by the BCM !
    Park, Tail, Marker and License Lamps
    The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
    Turn Signal Lamps
    The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
    Ground for the turn signal lamps is supplied as follows:
    ?€¢
    G101 provides ground for the left front turn signal lamp


    ?€¢
    G100 provides ground for the right front turn signal lamp


    ?€¢
    G302 provides ground for the left and right rear turn signal lamps

    May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

    2 Answers

    My turn signals and hazard lights stopped working


    Hazard switch..had it happen to my 2002 impala

    Dec 13, 2013 | 2001 Chevrolet Impala

    2 Answers

    2007 chevy impala brake light and left turn signal not working


    Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

    Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

    1 Answer

    How to install turn signal switch 2007 chevy impala


    Watch the video, it is a different model but the columns are the same. Cick HERE

    Jun 15, 2012 | Cars & Trucks

    1 Answer

    2007 chevy impala Shifter stuck in park


    Do you have brake lights? The brake switch on the pedal has to work to send a signal to a solenoid at the shifter to release park.

    Dec 04, 2011 | 2007 Chevrolet Impala LS Sedan New Cars

    1 Answer

    How do I change turn signal bulb?


    remove headlamp and go in from rear if in back remove tailamp and go in from rear

    Jun 28, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

    1 Answer

    How to change a turn signal on a 2007 impal


    Open the trunk, inside the trunk is a liner. Pull the liner back and you'll see the wiring going to the back of the light. Remove the light bulb retainer by unscrewing it and change the bulb.

    Apr 02, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

    1 Answer

    How to replace a turn signal light on a chevy impala 2007 ss


    Open hood. on top of headlight assembly you will find 2 small bolts. I believe a 10mm. socket should fit. Take the 2 bolts, out and remove complete assembly.

    Feb 01, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

    2 Answers

    04 impala turn signals stop and starti ntermitently


    The turn signal flasher is built in to the hazard switch. They are common for going bad. If the turn signals quit again, try pushing the hazard switch on and off a bunch of times really quick. If the turn signals start working again, replace the hazard switch

    Aug 31, 2009 | 2004 Chevrolet Impala

    1 Answer

    2000 CHEVY IMPALA WHEN AIRBAG LIGHT IS ON-NO TURN SIGNAL


    The only thing I can think of that would explain your problem is a faulty ignition switch.

    May 30, 2009 | 2000 Chevrolet Impala

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    61 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...