Question about Nissan Cars & Trucks
I have a 2005 nissan murano and when i start to drive a loud beeeeeeeeeeeeeeeeeeeeeeeep will start and stop after a few min then do it again usually 2-4 times then it will stop tell I stop my car as soon as I start it again it will do it again It didnt do this when I first got it then it started to do it once in awhile now every time I get in to go somewhere it very annoying please help I think it has sumtin to do with the GPS if that helps
Disconnect the batt or the computer a few min and see if it clears--if not then hav vehicle scanned
Posted on Nov 21, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Shortly after replacing the serpentine belt in my lancer, the same thing happened. It is NOT the timing belt. Belts squeal when they slip. If your timing belt slipped it would cause your car to run funny.
have somebody check the belt for wear (or do it yourself), replace if necessary. If it doesn't need replacement, just tighten it.
If you have the 4cyl engine that I have, the tightening is kind of a pain in the ****. Not a great design by mitsubishi. There's a pulley near the front right corner of the engine in front of the alternator. the belt should be running around this pulley GROOVE SIDE OUT. This is the tension pulley.
1) Lightly loosen the bolt in the center of the pulley (slightly loosen, DO NOT REMOVE).
2) Under that pulley there's another bolt. You can see that the bolt goes through a piece of metal
attached to the back of the pulley. Figure out which way you need to turn the bolt to move the
pulley toward the front of the car. (i don't remember if it's right hand thread, or left hand) This
puts extra tension on the belt. You probably don't need much. Over tensioning the belt can
cause pulley bearing failure. If you haven't done this work before, ask someone for
help. It's better to tighten a little bit, a few times rather than overtighten once.
3) Don't forget to ReTighten the bolt in the center of the pulley.
If there's lots of cracks and pieces missing on the ribs or grooves of the belt you should replace it first.
Posted on Mar 09, 2009
I had that happen too and found out that if you hold the unlock button down on your FOB for about 4-5 seconds then it will roll down the front windows. It's actually a feature, not a problem. You may have accidentally mashed something up against the FOB while it was in your pocket and you were within range of the car. That's what I did. Freaked me out the first time I walked out in the driveway and both front windows were down and I know I didn't leave them open.
Posted on Jul 21, 2009
You should also check and make sure all parts of the tubing are connected between the air filter and the throttle body. If one of these comes loose it will cause your murano to run like that. This is pretty common.
Posted on Oct 04, 2009
Tips for a great answer:
Sep 09, 2013 | Nissan Murano Cars & Trucks
Apr 07, 2013 | 2005 Nissan Murano
Jan 30, 2012 | Nissan Murano Cars & Trucks
Dec 01, 2010 | 2005 Nissan Titan
Jun 28, 2009 | 2005 Nissan Murano
Jun 07, 2009 | 2009 Nissan Sentra
Oct 16, 2008 | 2005 Nissan Murano
Sep 24, 2017 | Nissan Cars & Trucks
51 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: