Question about 2010 Mazda 3 2.5

Open Question

Fault code c1051 ssanyoung rexton - 2010 Mazda 3 2.5

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 ssangyong rexton, it cuts out when hot? theres a few fault codes come up, p1677, po675, po335 po372, any help would be much appreciated...


1677 may be Drive by Wire - MIL Circ. Short to B + Ssanyon is not listed as they use OEM parts.
0675 Cylinder 5 Glow Plug Circuit/Open
0335 Crankshaft position (CKP) sensor - circuit malfunction
0372 Timing reference, high resolution signal A - too few pulses

Jun 26, 2017 | SsangYong Cars & Trucks

1 Answer

Why doesn't the cruise control work?


run the fault codes
cruise control needs the following to work together as one or more will stop it from working.
VSS sensor, (road speed /speedo)
engine rpms/tacho
brake switch sensor/
clutch switch sensor
cruise control switch

Jun 06, 2015 | 2005 SsangYong Rexton RX

1 Answer

How can i deal with fault code 1235


Your vehicle is a rather sophisticated one. I don't recommend DIY. Your dealer or a very reliable repair shop should review. It may be as simple as bad electrical connections to sensors. But it could be serious problems. Prevention now may solve serious problems later.

Apr 01, 2015 | 2005 SsangYong Rexton

2 Answers

My 2005 Rexton 270 xdi will not start till slightly mobbed with aerosol.


I'm wondering why the guy who is holding the code reader can't tell you what it means ?
He is obviously not a Ssangyong specialist - or is it not a Ssangyong Scan100 gauge ??
I'm prepared to get you answers if I know it was done at a Ssangyong dealership on a genuine Scan100 gauge :)

This will take 24 hrs once I read your reply

Nov 07, 2014 | 2005 SsangYong Rexton RX

1 Answer

Ssangyong rexton engine check light


Check engine light comes on when computer detects an engine fault code. Light is to let you know that a fault code is stored in the ECM. You will need a diagnostic scan-tool to retreive stored codes. Hope that helps a bit.

Mar 07, 2014 | Cars & Trucks

1 Answer

Rexton 270 xdi


change all the fuel filters and bleed any air out of the system. Check the variable action of the turbo actuator and check that the vacuum hose to it is not brittle and cracked.. Run fault codes to see if any faults have been recorded

Mar 03, 2014 | Cars & Trucks

1 Answer

I have a 3.2 lt ssangyon and it cut off. after 10minutes of drive


Have you chceked the engine computer fro fault codes, this is done with a scanner.

Feb 13, 2012 | 2005 SsangYong Rexton EL

2 Answers

Rexton will not go past 2nd gear


Hi Belida, I'm very happy to be in Africa. Cold here means wearing my shirt buttoned up till about ten. I believe that the transmission may need to be diagnosed and the fault codes erased. Have that done and I believe it should also tell you of any other fault which may have affected the box, if any. I believe a simple reset will do the job for you. Brrrrrr....I'm answering you sitting here sweating, don't you just wish? Best regards John

Feb 12, 2012 | 2005 SsangYong Rexton

Not finding what you are looking for?
2010 Mazda 3 2.5 Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...