Question about Skoda Fabia

Open Question

Fabia 1.2 03 plate 16556 error lamba sensor has been renplaced

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 271 Answers

SOURCE: where is the lamber (or Lamba) sensor

Just follow the exhaust pipe from the engine to a first cataliser.The lambda sensor is on a pipe.Next to him is a connector box.

Posted on May 16, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My 206 1.1 keeps failing emsion test had new lamba censor and cat every running well but still failing c02

Well like you say ( lamba) means o2 sensor and cat .... New ? Co2 too much gas it could be bad fuel injectors ..... Check for codes the ecm have the most important info about it

May 15, 2015 | Peugeot 307 Cars & Trucks

1 Answer

Why can i select gear but no movement when clutch released

need to replace clutch disc /plate /pressure plate
check out axle if ok

Jul 27, 2014 | Skoda Fabia Cars & Trucks

1 Answer

How to disconnect reversing sensors skoda fabia estate 2009 model

remove socket , press all S.W in then turn to anticlockwise , pull out when . put new one , first pull the pin out , till come out longer .then press back (adjustment ) then turn clockwise

Jun 27, 2014 | 2008 Skoda Fabia 1.2

1 Answer

My corsa has had the lamba sensors changed front & back, but with no joy the engine management light is still on, could this be a ECU FAULT please help, the scanner is saying its the front lamba sensor...

what exactly does the code say? there are up to ten codes that can be set for any given 02 sensor. there are codes for sensor open circuit, sensor short to ground, heater open or shorted, slow response, lean or rich mix, as well as a couple which are activated by logical algorithms.
what do you mean by front and back? some cars have two sensors on the exhaust near the heads and two more in front and in back of just the catalytic converter. Details are necessary for quality advice

Mar 03, 2013 | Cars & Trucks

1 Answer

What do the white wires in the harness go to, I cut them off (accedent) and am not sure if I hooked them back right. also the 2 tan ones?

Not familar with american motors but i would hazard a guess and assume they are for the lamba sensor ,now the 2 white wires sre for the heatrer on the sensor so they can be connected anyway around but the 2 tan wires have got me as a lamba sensor uses two different colours for the filament in the sensor a gray and black is normal but it can vary although i have seen two black and two grays on some replacement sensors so just connect them up and if iam correct it should work providing that this is the lamba sensor wires you have cut through ,if iam right and the engine symbol light comes off reverse the two tan wires and clear the fault code and try again

Dec 19, 2012 | 1995 GMC Jimmy

1 Answer

Where is the lamber (or Lamba) sensor

Just follow the exhaust pipe from the engine to a first cataliser.The lambda sensor is on a pipe.Next to him is a connector box.

May 14, 2010 | 1999 Volkswagen Golf

1 Answer

Where are the oxygen sensors located on a 2000 dodge stratus(se), and will i need any special tools to replace them?

You mean Lamba sensor?
On the exhaust manafold.... you can't miss it it is the only sensor there!
Regards Bruce

Mar 12, 2010 | 2000 Dodge Stratus

2 Answers

88 nisson pathfider will not start

usualy if you can smell fuel while you crank it indicates that there is no spark or late spark, first i will check and make sure that the distributor rotor is ok and if it is the i assume the problem is in the timing belt, either it is broken or stripped either way the belt needs to be replaced

Nov 30, 2008 | 1988 Nissan Pathfinder

1 Answer


How about the MAF sensor?

Oct 18, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Skoda Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Brad Brown

Level 3 Expert

15633 Answers

Frank Magliocca

Level 3 Expert

1089 Answers

Are you a Skoda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides