Question about 2000 Jeep Grand Cherokee

1 Answer

How to change the back rotor - 2000 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

  1. Raise and support the vehicle.
  2. Remove wheel and tire assembly.
  3. Remove the caliper slide bolts .
  4. Remove caliper .
  5. Secure caliper assembly to nearby suspension part with wire. Do not allow brake hose to support caliper weight.
  6. Remove and discard the O-ring securing rotor to axle studs.
  7. Remove rotor off axle studs.

Posted on Nov 22, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it difficult to change a rotor and distributor cap and wires for a 1986 Chevy Nova? I have emissions inspection due this month and the plugs, rotor, distributor cap and wires were last changed in Dec...


I DONT KNOW WHAT STATE YOU ARE IN BUT EMMISSION ARE ONLY FOR CARS 94 AND ABOVE IN MOST STATES. ROTOR IS SIMPLE, REMOVE TIRE BRAKE S PULL PIN FROM ROTOR TAKE OF NUT WASHERS ECT, PUT IN A LITTLE AXLE GREASE IN ROTOR IN STALL BACK SAME WAY, -- BUT ME I WOULDNT CHANGE ANYTHING

Sep 14, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

I recently changed my rear brakes on my 2005 trailblazer and had the rotors turned. Now i have a grinding noise when i get up to 15mph and while braking.


Hello sweetascanb3,

A common problem is the emergency brakes drag on the inside of the rotor. The solution is to back off the adjuster. Another possible item is the backing plate they rust and distort and rub against the rotor, bending the backing plate so it doesn't touch the rotor is a fix for that problem.

Regards,
netvan

Feb 24, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

How do i change the brakes and rotors on my 2004


When you say fit properly I assume you mean it's not going back together. Make sure you have the bearings and races installed correctly on the back side and that you are installing the correct rotor on the correct side with the correct bearings. The front and rear bearings look the same but they aren't and if you try putting that rotor on with the front side bearing installed in the rear of the rotor it will never go back together.

Jul 12, 2010 | 2004 Toyota Sienna

1 Answer

My 2002 chevrolet 4wheel drive makes a noise alot like that of a break rubbing.It stops as the speed increases, I changed all four brakes and rotors and also changed the universal at the rear end. what...


Make sure backing plates behind front & rear rotors aren't rubbing on rotors. Jack up each wheel individualy & spin. May also be emergency brake shoes rubbing inside drum inside rear rotors.

Jun 24, 2010 | 2002 Chevrolet Silverado

1 Answer

How to remove rear rotor on 06 Acura TL


They are pretty easy. I just did my friends front rotors and pads on an 01' Acura TL's. Pull all wheels off. Take pads off shoud be a 14mm to take the calipers off. Compress the calipers. Hang up your calipers w/ wire or string so they are not hanging by the brake line. Next look on the back side of the carrier. There will be 2 17mm bolts holding a the bracket for the calipers and pads. If you have trouble breaking them free, use a brass or dead blow hammer on the wrench. (You will be doing the same to tighten the bolts back up.) Next there will be 2 phillips head screws on the rotors. Now these can be a royal pain to get out w/ out stripping the head of the scews. I used an impact tool w/ a hammer to get them out. The craftsman one runs about 30 bucks. (It is not an air tool. It just looks like an oversized screw driver. It is spring loaded, so when you nail it w/ the hammer you will want to twist at the same time and it will break the screws loose.) Once those screws are out pull the rotors off. Degrease the new ones and reverse the process. Make sure you use the impact tool to put the screws back in. Hopefully the rotors come w/ them.
If you change your rotors I suggest changing the pads also.
This was for the fronts on an 01 Acura TL. I do not know if there is a difference between the years. Pay close attention when you start to pull the rotor off. Should be the same process for the rear I do not know. The only thing that might be different on the rear is that the bearing is in the rotor. Check the back rotors to see what they are. (If bearings are in the rear rotors, buy Bendix rotors for the rear. They come w/ the bearing carriers already in the rotor so you do not have to press them in. Buy grease and rear seal for rear rotors. Pack the bearing w/ new grease, put seal in back or rotor, make sure it is flush and put the rotor back on.)

Oct 10, 2009 | 2004 Acura TL

1 Answer

How do you change the rear brake rotors?


jack the car take the tire off .remove the caliper ,,around middle of the rotor there is a small screw hole its is close to the tire screws you need to use a star key to take the screw off ,,that screw holds the rotor to the spindle once u take it off tap the rotor with a hammer gently to make it come lose sometimes u have to do that sometimes you don't need to ,,the rotor should come off easy ,,,replace it and put every thing back ..,,,Joe

Aug 30, 2009 | BMW 325 Cars & Trucks

2 Answers

Rear end noise on 2006 mitsubishi outlander


There is a race bearing on the back side of the rotor. If you haven't replaced it, I would strongly recommend it. You should change those out every time you change your rotors. Most new rotors come with new race bearings, if it did come with a new one (and it isn't shot yet), pull it out and pack it with grease. Wear latex gloves, put a pile of general purpose grease in your hand, and start stuffing the grease into the bearing until it comes out the other side.

May 27, 2009 | 2006 Mitsubishi Outlander

2 Answers

Problem changing rear rotors on 95 Toyota Avalon


Just remove the rear rotors, bull the straight off, after removing the caliper bracket. It would be a good idea to spray the small brake shoes with brake cleaner. No need to remove anything other than the rotor.

Mar 05, 2009 | 1995 Toyota Avalon

1 Answer

Changing rear rotors


The park brake shoes are on the inside of the rotors, you need to back off the adjustment on the park brake shoes to get the rotors off. They are cable operted and that is were the adjuster is.

Jul 20, 2008 | 2005 Dodge Magnum

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...