Question about 1999 Acura TL

1 Answer

2000 acura tl just flushed coolant, now no fan operation,fan is good of battery,sensing unit?relay?may not have disconnected ground at some point during coolant flush.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 20,706 Answers

Water pockets, you didnt burp it.

Posted on Dec 01, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

masterraphie
  • 41 Answers

SOURCE: starter replacement on acura 2000 TL 3.2

This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.

Posted on Mar 19, 2009

  • 1428 Answers

SOURCE: need the radio code. had work done and battery was

Visit http://www.radio-code.com/index.htm

Posted on Jan 08, 2010

  • 60 Answers

SOURCE: where is plug in acura 2000 tl for check engine

The OBDII connector is located in the center console just behind the ashtray. There is a plastic cover that must be removed and you will find the connector behind the cover.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coolant fan doesnt come on after flushing coolant


double posted. you left air in the system.

Nov 19, 2013 | 2000 Acura TL

1 Answer

2000 acura tl coolant fan after fluid change


New thermostat, installed, saw, new coolant made a little mess filling reservoir, (normal) checked fan fuse for some reason, and condenser fan fuse (xxx ?:), and temp guage, is slightly lower on gauge (than normal?) (disconnected xxxx? quit? a bit? to get to thermosta?.t no dash warning lights have a feeling I popped a relay.

Answer:

ok, you did a coolant service with STAT,

and it failed.

tell us what works right and wrong, symptoms only.

over heating? parked, (fan never comes on)? as it hits 225F?

under heating? ( fan stuck on , up North can cause huge cold engine)

dash gauge stuck low. (thermostat wrong heat range 180f is best. see FSM for spec. on this temp. spec..

Dash guage varies.? oddly (air in system)?

Dash gauge too high.? (Stat put in upside-down or bleed hole (jiggle) not UP side. higher side of mount , trapping air.)

Does something wrong happen only driving?

leaks?

does cap on rad hold 12-14psi pressure, hot.?

if car has fan belts, are they tight? (for sure water pump does)

Nov 19, 2013 | 1994 Honda Civic

1 Answer

96 acura tl 2.5l. havc diagnosis only indicates a fault in the blower motor circuit. The 30 amp fuse under the hood is fine. The relay in the under dash bank is good. High speed relay is good and...


power flows from fuse to blower motor relay. From there it flows to blower motor. Blower motor receives ground from two different places depending on which speed you choose. If you choose high speed, it gets ground through the blower motor high relay. If you choose any other speed, it gets ground through the power transistor below the right side of the dash. The power transistor regulates fan speed by pulsing ground on and off based on the speed you've set. Power transistor is most common failure point in these systems

Jun 27, 2017 | Acura Cars & Trucks

1 Answer

2000 acura tl ac heater fan wont turn on


my acura tl fan turn on when i turn on air conditioning why

Aug 22, 2012 | 2000 Acura TL

2 Answers

Vacuum hose diagram for 1999 acura tl 3.2


To reset check engine light... Disconnect the ground (black wire) from the battery. Wait for at least a minute for the computer to reset, then reconnect the ground. Start your car, and the light should not come back on.

Jun 27, 2012 | 1999 Acura TL

1 Answer

Hi. I do not get any heat from my 99 Acura TL. Fan and a/c working fine.


Check coolant level in coolant reservior. Also with the engine cold, remove the radiator cap and check coolant level. it should be full.
If you fluid levels are full have your mechanic check your heater control valve. It may need replacing.

Aug 26, 2011 | 2000 Acura TL

2 Answers

Installed B18 used engine now the radiator fan won't come on


If you used the sensors that came on the used engine, replace the coolant tempertur sensor. this should fix your fans

Nov 24, 2010 | 1995 Acura Integra Coupe

1 Answer

2000 acura TL horn blows when replacing the battery


dont you have the alarm key fob? if so that will reset it. just press unlock. If you dont an dits not a OEM Acura alarm you will need to find who makes it and get a new key fob, or have a shop that does alarms to disconnect it.

Oct 06, 2009 | 2000 Acura TL

Not finding what you are looking for?
1999 Acura TL Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...