Question about 2011 Chevrolet Equinox

1 Answer

Wipers wont work

How much can I expect repairs to run for control replacement or motor replacement? Is this covered under any warranty?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 12,223 Answers

See the diagram attached, and fix it. God bless you
test the switch for open or dirty, loose wires or connector and dirty or corroded, use the wd-40 for cleant, and of course test the motor for fault,finally test the FUSE or c.breaker However you can go to www.aa1car.com for help to fix it.


wipers wont work - 54284ff5-f9e0-4768-9b1a-c74e7111a0d9.jpg

Posted on Nov 20, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 299 Answers

SOURCE: 2004 chevy tahoe front wiper motor

You will have to remove wiper arms then the cowl cover.Should be visible from there.

Posted on Jun 16, 2009

  • 71 Answers

SOURCE: wiper motor replacement on 2004 tahoe

You need to remove your wiper arms and take off the plastic cowl panel.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

81 c10 silverado. Windshield wipers wont turn off, but the speed still changes


On the wiper motor is the speed control circuit board under the wiper motor cover, replace it.

Feb 16, 2012 | Chevrolet Silverado Cars & Trucks

1 Answer

Where is the wiper motor


How to change a wiper assembly & repair wiper mechanism on 2004 Audi A4

First time you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not, you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encountered fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!

Jun 19, 2011 | 2004 Audi A4

1 Answer

Window wipers sticking


How to change a wiper motor & repair wiper mechanism on 1998 Audi A4

First time you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

May 22, 2011 | 1998 Audi A4

1 Answer

How do I replace the windscreen wiper motor on an audi a4 2.5 tdi


How to change a wiper motor & repair wiper mechanism on 2004 Audi A4 2.5 TDI

First time you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Mar 30, 2011 | 2004 Audi A4

1 Answer

My front wipers arent working, could it just be the fuse? if so which fuse do i change as the list only has my rear wiper on it.


Fuse nr.31, F31, (25A) = Windscreen wipers
This fuse is placed on fuse box / relay plate engine bay 1, under bonnet in engine compartment area!

If the fuse F31 is OK.
You must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:
1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Jan 13, 2010 | 2006 Audi A3

1 Answer

Wipers will not work on low spped or intermittant


check out autozone.com. You have to register for a membership (free) but then you will be able to use any of their vehicle repair guides. I had a similar problem with a 1996 Jimmy that ended up being the wiper control module (~$30). The module is housed with the wiper motor, under a plastic cover. The motor should be located, under the hood, on the firewall, very near to one of the wiper arms. Simply, unplug the wiring harness to the motor and remove the 3 or 4 screws that hold the cover on and pull the circuit board straight out and replace it.

Nov 16, 2009 | 1997 Chevrolet Venture

2 Answers

How do you locate a windshield wiper blade motor in a 2000 Audi A


I had this problem two years ago on my 2000 Audi A4.
First you must diagnose this problem. In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works. Heed of the windscreen !!! Refit in reverse order.

Sep 11, 2009 | 2000 Audi A4

2 Answers

Where is the windshield wiper motor located on 2002 audi a4?


Bonnet lifted. The wiper motor is on left side at the bottom of windshield (for left hand steering wheel). In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works. Heed of the windscreen !!! Refit in reverse order. Please Rate my Response! Thanks!

Aug 19, 2009 | 2004 Audi A4

1 Answer

97 mazda truck wipers wont work


the motor ground is controlled by a solid state control module called the GEM (Generic lectronic Module), it is most likey burned out by the voltage surge of the strike, it is behind the radio, about 2" square and black plastic case

Jan 08, 2009 | 2007 Mazda B4000

3 Answers

Wipeers wont shut off


My 2001 Chevrolet Malibu had the same problem. The wipers would not stop. wipers wouldn't turn off. The problem was the wiper control module filled with water, seals break down with time. The wiper control module is attached to the front of the wiper motor under a black cover (three screws). I had to remove both wiper arms and the plastic debris guard between the window and the hood. Unplug the harness attached to the wiper motor, remove the three screws. The board is in te plastic cover. I pulled board out. dried it, put it back in and sealed the compartment with silicon. Works like new.

Sep 09, 2008 | 1999 Chevrolet Corvette

Not finding what you are looking for?
2011 Chevrolet Equinox Logo

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...