Question about Mitsubishi Cars & Trucks

Open Question

Brake light does not work, ABS light on, DTC C1340, replaced brake light switch

ABS light on, Brake lights doesnt work, DTC C1340, I have replaced brake light switch, still the same

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Brian032472
  • 150 Answers

SOURCE: Abs/Brake Light ON, although new brakes, ABS still works

I would suspect a speed sensor.

Posted on Jan 30, 2009

Ad
  • 116 Answers

SOURCE: Dash board parking brake and ABS lights stay

you have an abs fault. have your abs system scanned for codes.

your base brakes will continue to function normally

Posted on Apr 13, 2009

  • 2 Answers

SOURCE: transmission doesnt shift abs & brake light on speedometer doesnt work

I had the same problem with ABS light and speedometer, I was told that it is the transmission control module. It has not yet stopped shifting but I have had times where it just wont stay running. It will start and then stall. Hope this helps.

Posted on May 24, 2009

  • 1509 Answers

SOURCE: 1996 Chev Silverado K3500 dually, no brake lights

The chevys with red brake lights and turn signals do two things and I've fixeds alot of them. Looking at the tail lights with the hazard flashers on. both sides flash with nothingeles on? Or are the hazards yellow? if they're red and the third eye does work the turn signal switch is possible problem but it doesn't let the blubs and the circuit boards in the taillights out as they can fail and do some really bad stories the wires for the brakes and the turns and the hazards are the same ones and if the turns look right and the hazards look right then the turn signal switch transmites the turn too as this doesn't work part of your story can't be true

Posted on Aug 19, 2009

  • 497 Answers

SOURCE: 1996 rodeo, ABS/Brake warning light on dim, will

Get an OBD reading

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abslight stays on. How to fix? This is a2007trailblazer?


First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Dec 30, 2016 | 2007 Chevrolet Trailblazer

1 Answer

I have a 2000 Mercedes E430 base sedan. Last week I replaced the brake light switch because it was out and it solved the problem to the point that I can now put my car into gear and drive it, however, as...


Brake light switch problem may cause the ESP / BAS lights to illuminate.

Common symptoms of a bad
Mercedes brake light switch.
  • Car stuck in Park.
  • ABS ESP ETS lights come on.
  • Can not move the shifter from Park to Drive.
  • Brakes Defective Warning on Instrument Cluster
  • Car won't shift gears. Stuck in 2nd gear, limp mode.
  • Brake lights don't work. (Brake light switch can still be defective even if the brake lights work. Checking the brake light operation is not a good test.)
  • ESP, BAS, ABS lights turn on. Car won't shift properly. Stuck in gear.


TEST: To test your new brake light switch: Turn you car off to reset the ABS light. apply the parking brake. and start the car in neutral or park without using the brake. if the problem is the brake light switch... the light will only come on when you press the brake pedal.

If you replaced the brake light switch and the light is still on you should check a few other things such as:

  • Fuses and Relays
  • ABS pump
  • ABS wheel speed sensor
  • Brake Fluid Level
  • Get an advanced scanner to read trouble codes.


NOTE: ** You may need a MBZ scan tool to reset the error code which was stored in the ECU because of the bad brake light switch.

Feb 25, 2015 | 2000 Mercedes-Benz E-Class

1 Answer

Brake light flashes - abs lights stays on then they go off and a triangle with a circle around it comes on


I suspect bad Brake Pedal Position (BPP) switch. Check & replace if necessary the brake pedal position switch placed above pedals on the support.

tdisline_516.jpg

The best idea is to access the ABS ECU (Electronic Control Unit) using diagnostic equipment (VAS, VAG-Com, or similar) connected to the data link connector of the car, in order to pull out all DTC's (Diagnostic Trouble Code) memored. Then you will be able to replace bad pieces (e.g.: brake pedal switch, front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ABS ECU, in other words reset the ABS system and turn off the warning lamp on dashboard.
Good Luck!

Sep 13, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

I have a 2000 VW Beetle. My ABS light has been on for a while and last night my brake light and battery light beeped a few times then kept blinking. They finally shut off then about a couple of hours later...


I suspect bad brake pedal position (BPP) switch. Check & replace if necessary the brake pedal position switch placed above pedals on the support.
The best idea is to access the ABS ECU (Electronic Control Unit) using diagnostic equipment (VAS, VAG-Com, or similar) connected to the data link connector of the car, in order to pull out all DTC's (Diagnostic Trouble Code) memored. Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC's stocked inside ABS ECU & reset it.
Good Luck!

Sep 07, 2011 | 2000 Volkswagen Beetle

1 Answer

Yellow warning indicator lamp of a tringle with an excalmation point in the center and a counterclockwise arrow arround the triangle ---what does it mean?


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ABS & ESP ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS ECU & reset it.
tdisline_516.jpg
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: brake pedal switch, front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.
I'm convinced that your brake pedal switch is faulty because the glow plug warning sign went ON after ESP warning light. Just replace the brake pedal switch, see if rear stop lamps light when press the brake pedal, and test the car on the road.
Good Luck!

Sep 06, 2011 | 2005 Audi A4

1 Answer

I have a vw passat TDI130 2003. It runs really well, but engine workshop lights up along with the esp, abs and the glow plug indicators lighting up, most garages are charging just for a diagnosis to the...


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ESP & ABS ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ESP & ABS ECU & reset it.
I'm convinced that your brake pedal switch is faulty because the glow plug warning light went ON, along with the ESP & ABS. Just replace the brake pedal switch, see if rear stop lamps light when press the brake pedal, and test the car on the road.

May 20, 2011 | 2003 Volkswagen Passat

1 Answer

The esp light went on first and then the glow plug warning sign on my 2005 TDi passat. said workshop assistance, what is the problem


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ABS & ESP ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS ECU & reset it.
tdisline_516.jpg
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: brake pedal switch, front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.
I'm convinced that your brake pedal switch is faulty because the glow plug warning sign went ON after ESP warning light. Just replace the brake pedal switch, see if rear stop lamps light when press the brake pedal, and test the car on the road.
Good Luck!

May 11, 2011 | 2003 Volkswagen Passat

1 Answer

Where the brake switch on my polo 3003 model my brake lights dont work some told me its the switcc


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ABS ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS ECU & reset it.


1. Remove the cover panel above the driver's side foot well ...
2. Locate old switch, push in brake pedal, and twist switch body to remove ...
3. Unplug 4 pin connector from old switch and plug into new switch (it only goes one way...don't force it!). Insert new switch into frame and depress brake petal. You should turn it until it locks into place and is positioned like the original.


tdisline_439.jpg


4. Start the engine. Press the brake pedal once or twice and the EPC light should go out ...
5. Replace the cover over the foot well and you are done! If not, check the 4 pin connection and make sure it is fully seated in the switch. Also check to see if you can hear the switch engage when you press the brake pedal ... if not, you will need to remove the switch and adjust the push rod. The rod will move in and out for adjustment. Check to see if the brake lights come on when you press the brake pedal as well!

Apr 13, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

The brakes lights come on immediately after tuning the ignition on. the brake light remains on continously and only goes off when the engine is switched off. When the brake pedal is pressed when the...


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ABS ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS ECU & reset it.

Mar 23, 2011 | Audi A4 Cars & Trucks

1 Answer

Epc light on golf 1.6 se on and brake lights not working found out it's brake light switch but wouldn't know where to find it and don't want to go to dealers and pay ridiculous money would rather fix...


The brake pedal switch is placed above pedals on the support. If the problem still occurs you might access the ECM (Engine Control Module) & ABS ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored. Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ECM & ABS ECU & reset them.

Jan 21, 2011 | Volkswagen Golf Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...