Question about 1990 Toyota Corolla

Open Question

2E engine cylinder head bolt tightening torque

What is the tightening torque of cylinder head bolt of toyota corolla XE 2E engine 2002 model.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
joecoolvette
  • 5660 Answers

SOURCE: need the cylinder head torque settings on a toyota

Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Posted on Jul 25, 2009

Ad
  • 2 Answers

SOURCE: 1986 toyota corolla 2E engine high fuel consumption

why does my normal rpm always bug down when the engine start?and when I started to use the air con, the rpm was playing. It doesnt go on a certain point. it always range at 800rpm then it will down to 700. what am I might do to solve this probem?

Posted on Mar 13, 2010

Navmesha
  • 313 Answers

SOURCE: after torque specs for 1990 toyota corolla 1500cc

should come with the package containing the head gaskit or upper cylinder kit.Mostly at the back or printed inside the package.

Posted on Sep 10, 2010

  • 496 Answers

SOURCE: I need the torque settings

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Posted on Feb 22, 2011

solarstarene
  • 159 Answers

SOURCE: whats the valve clearance for toyota 4k engines

valve clearance is .20mm for the intake and .30mm for the exhaust. Will try to find cylinder head torque for you.

Posted on Mar 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota corolla cylinder head torque specification 1.6i 3zz engine


Cylinder head bolts are tightened in three stages:
Stage 1. 25 Nm.
Stage 2. 49 Nm
Stage 3. Rotate each bolt 90 degrees in a sequence.

Apr 11, 2017 | Toyota Corolla Cars & Trucks

1 Answer

Toyota 5afe head bolts torque


Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Mar 31, 2014 | 2003 Toyota Corolla

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

1 Answer

Torque specification


Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Jan 26, 2014 | 1993 Toyota Corolla

1 Answer

Torque specification


petrol engine alloy head 65lbs
main bearing caps 80lbs
big end bolts 40lbs

Nov 21, 2013 | Cars & Trucks

1 Answer

What is the torque setting of mains, bigends and cylinder head of 1zz Toyota corolla 140i


Torque:
- Connecting rod (big ends). Tighten bolts in several steps. 1st stage 29 NM, 2nd stage, rotate further 90 degrees
- Main cap bolts (crank shaft). Tighten bolts in several steps. 1st stage 44 NM. 2nd stage, further tighten 90 degrees.

Oct 06, 2013 | 2005 Toyota Corolla

1 Answer

I need the torque settings for a Toyota Corolla 1995 model 4afe engine TORQUE SETTINGS FOR THE CYLINDER HEAD? PLEASE PLEASE HELP


cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Feb 22, 2011 | 1995 Toyota Corolla

1 Answer

Whats the torque setting for big end bearing bolt and cylinder head bolt for toyota corolla 12 valve 2E,1990.


hi big end bearings are two stage, 25nm leave ten mins, then 49nm cylinder head bolts three stages 20nm leave ten mins, 40nm leave ten mins then 60nm check after 5,000miles hope this helps

Apr 07, 2010 | 2000 Renault 181

2 Answers

Need the cylinder head torque settings on a toyota corolla 1990 model ae92 wiht a 4a-fc engine


Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Jul 25, 2009 | 1990 Toyota Corolla

Not finding what you are looking for?
1990 Toyota Corolla Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...