Question about Cars & Trucks

Open Question

Isuzu nps 300 4x4 front hub wheel beating inspection

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 138 Answers

SOURCE: 1989 isuzu trooper autolocking hubs

The autolocking hubs are vacuum operated.. Check the small hoses at the back of the hubs for cracks or a broken off fitting.

Posted on Dec 31, 2008

countrysi248
  • 443 Answers

SOURCE: clicking noise from front hubs 2004 dodge ram 2500 diesel 4x4

First just crawl under it and grab your axles and see if you can shake them and get any movement from either of them this will tell you if you have a loose CV joint or not .. thanks Jerry holler if you need more .

Posted on Jan 30, 2009

  • 447 Answers

SOURCE: 2000 Dodge Dakota 4 wheel drive hub wont budge

These can REALLY stick solidly in place. I usually get them off with one of two methods: A big slide hammer attached to the wheel studs using a hub adapter or by pushing against one of the hub mounting bolts using my biggest air hammer with a flat hammer bit in it. You will wreck the head of the bolt doing this so you need to have another one on hand if it comes to that. I turn the bolt nearly all the way back in so there is just an 1/8" of room between the head of the bolt and the steering knuckle [to provide the maximum thread surface on which the force will be applied] and then rattle on it with the air hammer unit it moves a bit. You may need to move this bolt around to the other holes to work the hub free. Clean the corrosion and rust out of the bore that the hub mounts in before installing the new hub so it will go back in properly. Hope this helps a bit and good luck!

Posted on Jul 02, 2010

  • 72 Answers

SOURCE: i have a 1997 isuzu

just the lugs can be replaced. about $2 a piece at local parts store.
removing tire brake caliper and bracket and disk. use a pin chisel and sledge to pop them out. insert new ones slide rotor on screw in a lug nut to pull the bolt trough. (its pressed in). use grease on bolt and nut so it wont seize and strip. repeat for other 2

Posted on Mar 14, 2011

  • 5370 Answers

SOURCE: procedures for and proper preload

The hub nut are to be removed by a tool. You can get Hub nut tool from NAPA should be #3375.

--------
Its a complete procedure to replace the bearings.Please click this link below and follow the procedure to replace the front wheel hub bearings:--- http://technoanswers.blogspot.com/2011/06/how-to-replace-front-wheel-hub-bearings.html ---------- This should help.Thanks.Helpmech.

Posted on Jun 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I NEED TO SEE A SCHEMATIC PICURE OF WHEEL BEARINGS ON THE FRONT WHEEL 4 WHEEL DRIVE OF A 1992 RODEO ISUZU


Check with local parts store they often have blowup they can print off or purchase a vehicle specific repair manual..Chilton or haynes are best.

Aug 24, 2016 | 1992 Isuzu Rodeo

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

I have a knock in the front end of a 1993 isuzu rodeo when in 4 wheel drive, only when going up hill. I've also had problems w/ the auto locking hubs disengaging. Could this be related? How do I insta


Your problem may be as simple as a bad ball joint, CV joint, tie rod end, hub assembly or other front end part. Something is not tight anymore. Have the front end checked and go from there. GOOD LUCK FRIEND.

Nov 15, 2014 | 1993 Isuzu Rodeo

2 Answers

4 wheel drive not working won't engage front


have you checked the front hubs are engaged or engaging

Jan 20, 2012 | 2000 Isuzu Rodeo

2 Answers

My 4 wheel drive quit working in my isuzu trooper i can see the front drive shaft turning but the front tires are not spinning


do you have auto locking hubs? if so save yourself the hassles i did not and buy a decent set of manual hubs.my 1989 4 wheel just gave up one day..no wear on axles..front drive shaft spinning but no action..i replace auto locking hubs and re assembled to no avail...no answers why either...have pulled it all apart and put back together many times and no change,only to be told to put manuals in and live happily ever after!!done ....and done!

Jan 08, 2011 | 1989 Isuzu Trooper

3 Answers

2005 equinox wheel bearing assy wont come out


okay i assume the rotor is off,remove the bolts out the back, take a hammer and beat the front of the hub the top then bottom then the sides to free,hit so that hub pull out,you will be hitting the back side the hub where the wheel would sit,if that doesnt work then use a chisel to break free, stick it where the hub meet spindle,ITs just frozen beat it.a56579d.jpg

May 15, 2010 | 2005 Chevrolet Equinox

1 Answer

1989 isuzu trooper right front wheel clicking and does not engage in 4 wheel drive (when all four wheels are in the air)


Check the automatic locking hub on the right side. BEWARE: You MUST have the appropriate special service tools for this job!!!!!

The vehicle will not engage in 4WD operation when the vehicle is off the ground, as the automatic locking front hubs require front wheel load to engage. When the hubs DO lock, it is normal to hear 2 to 3 soft clicks. Anything after that indicates a problem.

If memory serves, there is a cam bushing behind the plate that will wear out, and if the plate is worn out, the hub clicks and will not engage.

Jan 07, 2010 | 1989 Isuzu Trooper

1 Answer

Front Wheel Bearing on 4x4


If you have a good ear and feel for it, you can raise the wheel and spin it and listen for a slight grinding noise or you might be able to feel roughness when the tire spins.

Otherwise, the bearing(s) will need to come out and be inspected for pits.

I doubt you'll have to replace the hub. The bearing and race usually take the beating, protecting the hub.

But, to answer your question, the hub usually comes off easily after removing the axle nut. On SOME vehicles this is not very easy, and a repair manual would be the best way to get this procedure if you need it.

May 06, 2009 | 2004 Nissan Titan

1 Answer

1989 isuzu trooper autolocking hubs


The autolocking hubs are vacuum operated.. Check the small hoses at the back of the hubs for cracks or a broken off fitting.

Dec 31, 2008 | 1989 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...