Question about 2004 Nissan Armada

Open Question

Neutral safety position

Car cranks over but wont start is there a inertia switch i can press to allow the fuel pump to work

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 26 Answers

SOURCE: 1993 nissan sentra sparkplugs are getting wet car wont start

Your timing chain may need replaced.
Sounds like your plugs are sparking too late or too early.
or the gap is too big in your plugs. ( get a gapper and regap to .08 ish.. )
Try these

Posted on Sep 10, 2008

Ad
  • 154 Answers

SOURCE: no power at ineartia switch

try running power from relay to the inertia switch through a jumper wire and see if pump works. you might have a pinched or broken wire in the factory harness.

Posted on Jun 10, 2009

rteemon
  • 578 Answers

SOURCE: my 2001 Nissan Pathfinder engine cranks, but won't

check you spark plug and distrubitor

Posted on Jul 01, 2009

  • 3 Answers

SOURCE: Cranking but doesnt start, or intermittently not starting

My car does the same thing...sometimes it wont start....have to turn the key off then when I crank it again it fires right away. Possible that the in tank fuel pump pressure regulator isn't building to the proper pressure. Nissan did post a recall....under warranty *recall* I might add.... there is an updated pump that will cure the problem but since you most likely are out of warranty it will cast $400+ for the part plus labour if you can't install it yourself. Call nissan to verify if your car is affected by referencing your VIN with them. Dave.

Posted on Jul 15, 2009

  • 811 Answers

SOURCE: car will start but won't keep running

run scanner for trouble codes, some auto parts store will do this for free 

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 Hyundai sonata died while driving and will not start turns over cranks but wont start fuel pump? crank shaft position sensor ? where is the location of fuel shut off value help


no inertia switch or fuel switch--fuses or relays ---to test the fuel pump easiest is to spray starter fluid if it fires you have a fuel problem if doesn't fire look into ignition [ spark]

May 28, 2016 | 2001 Hyundai Sonata

1 Answer

Why wont my car start gauges and lights come on but wont crank no power going to soelinoid wire


If the security system has been reset ( no light on/flashing ) you may have a neutral safety switch problem, Will the vehicle crank over in neutral? In most cases, the neutral switch grounds the starter relay and allows it to operate. Does the starter relay connector have 2 powers? One constant and one with key on/cranking? If these power supplies are there, suspect the ground side of the relay to be the problem and possible neutral safety switch

Jan 20, 2016 | 2000 Ford Taurus

1 Answer

What all safety switches are on a 1996 ford thunderbird


I think the only safety switch in the starting circuit (which just engages the starter motor to crank the engine over) would be the neutral safety switch. But if you have the anti-theft system, that will inhibit starting while honking the horn and flashing the headlights, too.
There is an inertia switch in the wiring to the fuel pump which could trip with a large bump, but it would only shut off the fuel pump, and not affect the starting circuit.

The neutral safety switch wiring would be found in the wiring to the Transmission Range sensor, which also needs checking.

Sep 21, 2015 | 1996 Ford Thunderbird LX

1 Answer

2010 nissan versa got in a collision. Wont crank over. Would the fuel inertia switch cause this?


Fuel inertia switch stops the fuel pump running in the case of a collision causing a broken fuel pipe which otherwise could spray a litre of petrol every few seconds and rather spoil someone's day.

Certainly a tripped inertia switch would prevent the engine from starting but I doubt it would stop the engine cranking, though I don't have up to date information on the model and there could be different safety regulations where you are.
The inertia switches are accessible and resettable so why not just reset it and try again. Your vehicle handbook will have the details.

An immobiliser stops the the engine cranking on some vehicles as well as stopping the spark and injection and often the fuel pump.
Bridging the battery positive wire to the solenoid to make the starter crank the engine won't be switching the rest of the stuff back on.

Feb 06, 2015 | 2010 Nissan Versa 1.8

1 Answer

2005 Dyna Superglide laid it down on the brake side bent up my handbrake and my foot brake other than that maybe a mirror got scratched nope problems with it other than that picked it up when to start it...


Turn key,listen to the whine of the fuel pump priming,start bike. If you don't get the sound of the pump priming either it's not getting power or it's dead, I don't think it has a inertia safety switch.
OR
the crank sensor is the only sensor that, if faulty, will not allow a bike to run. However, even with a bad CS the bike should still 'prime' when you turn ignition on and switch to the run position.
( if it doesn't, I'd look for power to the pump)

Nov 18, 2013 | Cars & Trucks

2 Answers

Wont start unless in neutral


Parking and Neutral positions, both have switches to allow for starter cranking. Probably you need to replace the Parking position start switch.

Nov 12, 2013 | 1993 Dodge Caravan

1 Answer

Wont start but lights work


You really need to describe more about this problem. Does the motor crank over? What Year, Make, and Model?

The 2 most common problems are the Inertia switch cutting off fuel pump power so that you can crank the engine and get no fuel; and that the Brake pedal safety switch is broken and out of position causing the engine not to crank.

So look up more about your individual car and reference whether your car has the parts on it to experience these problems.

Aug 25, 2013 | Ford Mustang Cars & Trucks

1 Answer

No fire to coils in 04 Mazda RX8


Check for inertia safety switch, if its not gettin fire to the fuel pump it wont spark either.

Feb 22, 2013 | 2004 Mazda RX-8

1 Answer

What typically is needed to to be done if a 2001 supercrew has had air bags deployed and wont start after that. The switch in the right kicker panel for the fuel pump does not appear to have been tripped....


Good info on the PATS / theft light. Looks to be the PATS / HEC operation is functioning correctly

The Fuel inertia switch only cuts power to the fuel pump, so if tripped, the truck would have a crank no start issue. Do you have a crank no start, or no crank issue.

To reset, just press down on it. To check if the switch is tripped, check for power at the connector to the fuel inertia switch

Engine compartment fuse # 10 ( 20A ) to the fuel pump relay -> Dark Green w/ yellow stripe wire to the fuel inertia switch -> pink w/ black stripe wire to the fuel pump module.
Check the pink w/ black stripe wire to ground with a meter for power, with the key in the run position.

If you turn the key from off to run ( do not start ) you should hear the fuel pump cycle ( hum, then turn off ).

Could be an issue with the fuel pump relay ( my '01 had a crank no start at ~ 35K miles, bad fuel pump relay ). I proved this out ( after a stupid ID10T error in my diagnoses process ) by jumpering the normally open contacts in the fuel pump relay socket, and then installing the trailer tow reverse circuit relay into the fuel pump relay socket ( same full size Ford Relay ).

Jumpering the fuel pump relay in the relay socket ( remove relay and use jumper wire ), red line
sscullys_16.jpg

If you have a no crank issue, could be the DTR ( Digital Transmission Range ) sensor on the driver's side of the trans is out of alignment.

Check the start motor relay ( on the firewall on the passenger side ) for power on the Tan w/ Red stripe wire when the key is in the start position ( this is from the ignition switch through the DTR when in park or neutral to the starter motor relay ).

You can test another route, turn the key to the run position, and apply power to the Tan w/ Red stripe wire on the starter motor relay in the engine compartment on the firewall. BE CAREFUL, the motor should turn over, keep clear of moving parts.

Post back a comment to this problem with the results of the testing.

Thanks

Nov 03, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Wont crank or do anything.


I have 1994 for escort 1.9 5speed doing the same thing. Will not start with the key but will start if you jump the starter

Apr 26, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
2004 Nissan Armada Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...