Question about Subaru Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The torque converter clutch circuit may be at fault. The best way to determine the problem is to have a scanner/computer to read check engine codes.
Posted on May 06, 2009
Chances are it is a bad ABS sensor. Need to get scanned to know for sure and which one.
Not much i know but I hope that helps.
Posted on Feb 03, 2010
I HAD THIS SAME PROBLEM BACK IN AUGUST. GO GET YOU TIMING CHECKED I DID NOT AND I BLEW MY ENGINE. SUBARU TOLD ME I "OIL STARVED" THE ENGINE AND DID NOT HONOR THE WARRANTY FROM WHAT I HAVE SEEN ON THE WEB THIS HAS HAPPENED ON MORE THEN ONE OCCASION. LONG STORY SHORT I GOT THE CHICKEN AND EGG STORY WHAT HAPPENED FIRST TIMING WHEEL BREAKING AND CLOGGING THE OIL OR OIL NOT RUNNING PROPER AND THE TIMING WHEEL BREAKING. NOW I HAVE A CAR SITTING IN MY DRIVEWAY WAITING FOR A TEN THOUSAND YES TEN THOUSAND DOLLAR ENGINE. AND THREE MORE YEARS OF PAYMENTS
Posted on Feb 28, 2010
SOURCE: ESP/BAS warning light on. went
Hi, these systems are all linked together. Most commonly, one of the wheel speed sensors is not reading or is reading incorrectly. This can also occur on slippery surfaces where one or more wheel slides enough to cause the sensor to drop the signal, but not enough to meet criteria for an abs or esp episode. If the light comes back every time you turn on the ignition, there is a deeper problem.
The system has detected a fault in the electronic stability program - brake assist system. You have an electrical connection at the rear wheels secured to the inside of the brake area and are viewable from under the vehicle. It is a small wire harness running to each wheel. Grab the connector and wiggle it around, and make sure they are tight. Due to the connector being mounted low to the ground, sometimes they become dirty or corroded, not making contact. Do this on both sides and see if the lights turn off.
If the light does not turn off, you have to replace dynamics sensor, which is mounted UNDERNEATH the center console in the car. There is a "lost communication to dynamics sensor" and "low voltage to dynamics sensor supply"..
Posted on Feb 13, 2011
SOURCE: 2008 wrangler. abs, esp and
Check first the third eye brake light. does it work? okay the problem reside in a ABS sensor make sure it is hook up or if you recently did a brake job it didnt get contaminated. When the ABS signal is interfered with ESP,Traction is disabled. One or some of the wheel speed sensor is disconnected or is being interfered with. This is common for a recent brake job if any occured
Posted on Apr 23, 2011
Testimonial: "replace pads about six weeks ago. may have an issue there. thanks. I can check that myself. very helpful"
Tips for a great answer:
Nov 24, 2015 | 2008 Subaru Legacy
Feb 17, 2015 | 2008 Cadillac Dts
Sep 08, 2014 | 2011 Subaru Impreza
Jan 09, 2014 | 2004 Subaru Outback
Dec 31, 2013 | 2006 Subaru B9 Tribeca
Mar 15, 2013 | Cars & Trucks
Jun 01, 2010 | 2000 Subaru Forester
Jan 27, 2010 | 2006 Subaru B9 Tribeca
Oct 11, 2009 | 2008 Subaru Impreza
52 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: