Question about Cars & Trucks

Open Question

How do you change clutch master cylinder 97 Toyota hilux ln167 3lt?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
hank5899
  • 151 Answers

SOURCE: 97 chevy cavalier 2.2l 5sp clutch problem

get the hyd clutch system assembly complete and pre-bleed from the dealer

Posted on Sep 07, 2008

Ad
  • 10 Answers

SOURCE: ford focus st170 clutch master cylinder

To replace the clutch master, you must remove the under hood fuse box and air filter housing assm, then remove the hydraulic line that goes into the inlet port of the clutch master, then inside the car, remove the hush panel/knee bolster panel from under the steering column, and loosen the boilts that retain the brake pedal to the firewall, then remove the two 10mm bolts that secure the clutch master to the brake pedal assm. Reverse procedure ti install, then fill the brake master cylinder with clean fluid, loosen the bleeder screw at the top of the trans, and bleed the clutch as you would the regular brake system, but never pump the pedal, tighten screw, with foot off of clutch pedal open screw and press pedal to floor, then tighten screw before you release pedal, then release pedal loosen screw, etc. until no more air comes out, it may take quite a few times to fully bleed the system.

Posted on Feb 07, 2009

motor1258
  • 6674 Answers

SOURCE: remove master clutch cylinder on 1992 bmw 325i

Perhaps this link will be of some help.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004a3c7

Posted on Feb 18, 2009

  • 20 Answers

SOURCE: 1979 Toyota Hilux alternator wiring

always, counterclockwise starting with blue, then yellow, then red

Posted on Apr 26, 2009

  • 3 Answers

SOURCE: hilux clutch master cylinder seals

The seals face towards the hydraulic side. Install with the wide side of the seal towards the hydraulic line. Note: it will not bleed like a brake system. Fill the resivoir and open the slave bleeder and gravity bleed, that will get you about 90%. Then get somebody to step on the pedal while you ,now, bleed it like a brake system. Good Luck!.

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The clutch pedal of my Toyota Hilux kzte 2004 does not want to release on its own.


I assume that means that the clutch does not engage/disengage when you press and release the pedal. There are a number of possible issues here. First, does the pedal feel "soft"? Is it easier to press down that usual? If so, the problem may likely be in the hydraulics of the clutch. A bad master or slave cylinder will not allow hydraulic pressure necessary to engage/disengage the clutch.
If the pedal feels normal, then the problem is most likely internal to the clutch mechanism. A bad release bearing or a stripped clutch disc are the most likely culprits for this issue.

Sep 10, 2016 | Toyota Hilux Cars & Trucks

1 Answer

I have a Standard 97 Toyota Celica,1.8 Engine..When I put my car in Gear the RPMs Rev up to about a 6-7 But the car Does Not Move..Hoping someone can help.Thank You in advance


manual or auto would be a big help
If manual check clutch operation
cable clutch --replace cable
hydraulic clutch ---replace clutch master cylinder
Auto check for torque converter clutch servo/solenoid problem or TCM or selector linkage

Dec 31, 2015 | Toyota Cars & Trucks

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

1 Answer

How to change a clutch master cylinder on a 2006 toyota tacoma


remove line from the side of clutch master cylinder two bolts or nuts on firewall inside vehicle is a pin on the upper side of clutch remove and pull old unit out bench bleed new master by filling and pressing in on the piston of the master cylinder. if you dont have a hose fitting dont bench bleed bleed it in vehicle( this method takes longer) install back in vehicle and hook it all back up torque bolts to 25 ft lbs then bleed the slve cylinder from under vehicle near back of motor just like bleeding brakes pump up hold and release the line pressure by opening valve on slave cylinder.

Apr 06, 2013 | 2006 Toyota Tacoma

1 Answer

Bleed hilux brakes


Brake Pedal will be hard with engine off & a couple pumps
of the pedal,will bleed off vacuum,that is normal

System not properly Bleed or Master Cylinder is leaking

Jan 08, 2013 | Cars & Trucks

1 Answer

85 hilux 4x4 have no clutch when checking found fluid leaking from rubber boot at the arm pretruding from gear box how do you repair this? cheers roger


bad slave cylinder possible. may even be a bad clutch master cylinder.was leaking from firewall? not bad clutch mastercylinder. was leaking under car on passenger side at front of tranny, but in between motor and tranny where motor bolts to transmission? most likely, bad clutch slave cylinder. having to add brake fluid to clutch master cylinder? having to pump the clutch pedal up to shift gears? either you have a bad clutch slave cylinder[leaking under the car between motor and tranmission] or leaking on firewall [the wall that under dash and under the front window] you may even need a clutch replacement.3 if you need further assistment,repost your question to fixya.com

Dec 26, 2010 | 1985 Toyota 4Runner

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

1 Answer

84 4speed manual diesel hilux


Yes, there are two adjustments for your clutch available, one can be found at the back of the primary clutch master cylinder and the other one is the rod sticking out of your secondary clutch master cylinder. it's very tricky though, make sure to turn those adjustments a turn at a time. small turn makes a big difference. make sure to bleed your system afterwards.

Nov 21, 2008 | 1995 Toyota Pickup

1 Answer

84 hilux clutch


Have your primary clutch master cylinder (found on the engine's firewall) and the secondary clutch cylinder (found at the side of the bell haousing of your transmission) checked. It is hard to convert your kind of transmission into cable type, cables pull while fluid type clutch push, just have it repaired.

Nov 21, 2008 | 1995 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...