Question about Dodge Ram 2500

Open Question

Iat sensor look like on a 1998 dodge 2500 v10

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 114 Answers

SOURCE: iat sensor

Hi there ... The IAT sensor is on the intake manifold, just behind the alternator. For further info on this sensor you can go to www.autozone.com. click on repair info,select your vehicle. then click on vehicle repair guides. In the product search box at the top left type in IAT and then click on the repair guide in the box that appears and it will give you more info.

Hope this helps you out

Posted on Jan 23, 2009

  • 4 Answers

SOURCE: 2001 dodge 2500 v10 has low idle

On my 06 v10 there is a idle adjustment screw at the linkage on the throttle body.
clean air filter
clean sensor in the air intake ram
try some 93 octane

Posted on Feb 04, 2009

farroutideas
  • 78 Answers

SOURCE: where is the iat sensor on my 2005 dodge ram 2500

Hi there:

If your truck has a 3.7L or a 4.7L engine it is on the right side of the air box just on the engine end of the flexable rubber boot that extends from the right fender. If it is a SRT it is located in the rubber boot that extends from the front of the truck on the left hand side of the boot just before it connects to the engine.

Hope this helps
Farrout!

Posted on Mar 18, 2009

emissionwiz
  • 75822 Answers

SOURCE: IAT sensor location

here is a picture


0d597dc.jpg

Posted on Mar 09, 2010

  • 1348 Answers

SOURCE: 2001 dodge ram 2500 v10 oil pressure drops to 0 then back up

you need to put an oil pressure gauge on it and see what happens.what you will find is that the sender unit is no good.

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 dodge ram truck 2500 2wd code reader says 4 codes dont know what they mean p1509, p1298, p0118 andp0113


P1509 Dodge - Leak Detection Pump Switch or Mechanical Fault

P1298 Dodge - Air/Fuel Ratio Lean Under Wide Open Throttle Condition
- Plugged air filter
- Plugged fuel filter
- Defective fuel pump
- Ignition system weak-misfires
- Defective coil

P0118 Dodge - Engine Coolant Temperature Sensor Circuit High
- Low engine coolant level
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection

P0113 Dodge - Intake Air Temperature Sensor 1 Circuit High
- Faulty Intake Air Temperature (IAT) sensor
- Dirty air filter
- Intake Air Temperature (IAT) sensor harness is open or shorted
- Intake Air Temperature (IAT) sensor circuit poor electrical connection

Dec 16, 2013 | Cars & Trucks

1 Answer

On my 1998 ram 2500 V10 the oil pressure sensor isnt getting power but i do have good oil pressure what could be the problem


it is common for the sensor to go bad and make it look like you have no pressure if you had no oil pressure it would make some noise

Jun 19, 2012 | Dodge Ram 2500 Cars & Trucks

3 Answers

I cannot find the IAT sensor on my 2001 dodge ram v10


Its hidden on the drivers side. its just below the 3rd bolt back for te upper plenum, count the bolts back and look down on the lower intake.

Aug 30, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

I have a 2001 dodge 2500 v10 gas. When started it runs rough regardless of temp. Code says mixture is too rich. The problem goes away if engine rmps are held between 3 and 4 thousand for about a minute and...


I commend you on your tenacity. I guess the code is P0172. So you have metered air due the the MAP and IAT in combination and good engine coolant signal but still too rich and runs rough. It all points to a leaky fuel pressure regulator valve.

Jun 24, 2010 | Cars & Trucks

1 Answer

2001 dodge ram 2500 v10 oil pressure drops to 0 then back up


you need to put an oil pressure gauge on it and see what happens.what you will find is that the sender unit is no good.

May 18, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

Where is the IAT sensor located on dodge neon


Right next to the intake plenum.

Feb 04, 2010 | 1998 Dodge Neon

2 Answers

Where is the cam sensor located on a dodge v10


It is located under the injection pump but you may have to pull the pump to get it it a tight fit.


Sep 21, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

2001 dodge 2500 v10 has low idle


On my 06 v10 there is a idle adjustment screw at the linkage on the throttle body.
clean air filter
clean sensor in the air intake ram
try some 93 octane

Feb 04, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Water pump


go to this link it tells you everything


http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Engine+Mechanical&partName=Engine+And+Engine+Overhaul&pageId=0900c152800c06ce&subChapterTitle=Water+Pump&partId=0900c152800c06c1

Dec 30, 2008 | 1998 Dodge Ram 2500 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...