Question about Oldsmobile Cars & Trucks

Open Question

Replaced crank sensor in dodge truck now ticking sound

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fixincars
  • 335 Answers

SOURCE: crank shaft sensor

That is definately the most improper way to go about the diagnostic process i realize that it costs money to take it to a shop but you have already spent more than it may have cost to properly fix it. Your vehicle is so new even if you change evrything you may not make it start it does not have to ne a "failed" component"
You are are going to have to take the truck to an OBDII shop and have it diagnosed you have no chance of "hitting" it There are security system issues possible and you cannot go on another persons experiences same truck, same engine, same color everything same symptoms and it can be an entirely different problem. Stop now and take it to Dodge and be done with it Believe me unless you own an OBDII scan tool and have many years of diagnostic experiience you are likely not going to fix this one ,sorry anyway what are your symptoms? Exactly every detail

Posted on Aug 24, 2008

Ad
  • 201 Answers

SOURCE: 1992 dodge 318 engine turns over, but no start. No

if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

Posted on May 09, 2009

  • 17 Answers

SOURCE: 1997 Dodge Caravan won't start - has a tick tick sound

It sounds like the crank shaft sensor is hitting when you spin it over. It is probably in too far. There is a piece of card board stuck to the end of most of them to set it correctly. If it is not the the magnet will pull it to the metal reluctor. Pull it out and see if the end is rubbing. Then take a piece of card board from the box the sensor came in, put a dab of grease on the end of the sensor eg: magnet and put it back in, when it spins over the card board will be rubbed of. That should give you enough clearence for the magnetic sensor to work and not rub eg: the ticking noise.

Posted on May 31, 2009

polarcycle
  • 1392 Answers

SOURCE: Replaced the harmonic balacer & crank sensor but it will notcrank

It sounds like you have a bad battery if it isn't turning over fast, and you are getting rapid clicking.

Posted on Jul 10, 2009

  • 76 Answers

SOURCE: 1993 DODGE DAKOTA V8-318 5.2L EVERY 3 TO 5 DAYS

possible you ignition switch

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 Dodge Caravan is making a ticking sound what do I do


I would need to hear this noise to make a diagnosis, anything else would be a wild guess.

Sep 23, 2016 | 1996 Dodge Caravan

1 Answer

Replaced crank sensor now ticking noise


the sensor not to correct deepth the air gap is not correct

Nov 19, 2013 | 1992 Dodge Ram 150 Club Cab

1 Answer

Cpm malfunctioning: cranking sensor replace:


CPM? Isn't that the cam position sensor? That sensor is to let computer know when to pulse the injectors.

Aug 20, 2013 | 2000 Dodge Ram 1500 Truck

1 Answer

2003 dodge caravan 3.3l cranks but no spark have replaced timing chain my bad...but i have a clicking noise sounded like chain.....replaced crank sensor it had evidence of being smaked maybe causing my...


probably forgot to reinstall camshaft sensor which located on timing cover or forgot to reconnect camshaft sensor because crankshaft sensor and camshaft sensor work together to control fuel timing and spark timing.make sure ignition coil getting 12 volts.

Aug 11, 2013 | 2000 Dodge Grand Caravan

1 Answer

3.8 in 98 dodge caravan cam and crank sensor go in and out of sink no start timing chain and gears have been replaced and both sensors no codes


Cam and crank sensors both have to be gapped. A couple pieces of masking tape on the end works great. Sounds like one of ur sensors is hitting tone ring

Apr 17, 2013 | Dodge Caravan Cars & Trucks

1 Answer

I have a 2001 dodge stratus it won't start it cut


sounds like the timing may be a bit off, then the heat near the siloniod is causing it to crank over

Apr 07, 2013 | Cars & Trucks

1 Answer

Replaced the harmonic balacer & crank sensor but it will notcrank


It sounds like you have a bad battery if it isn't turning over fast, and you are getting rapid clicking.

Jul 10, 2009 | 1993 Buick Regal

1 Answer

1997 Dodge Caravan won't start - has a tick tick sound


It sounds like the crank shaft sensor is hitting when you spin it over. It is probably in too far. There is a piece of card board stuck to the end of most of them to set it correctly. If it is not the the magnet will pull it to the metal reluctor. Pull it out and see if the end is rubbing. Then take a piece of card board from the box the sensor came in, put a dab of grease on the end of the sensor eg: magnet and put it back in, when it spins over the card board will be rubbed of. That should give you enough clearence for the magnetic sensor to work and not rub eg: the ticking noise.

May 30, 2009 | 1997 Dodge Caravan

4 Answers

Crank sensor location 1999 dodge durango


the crank sensor is located passenger side back of the engine were the trans and engine come together .there are 2 - 13mm.bolts that bolt to top of the engine.

Feb 22, 2009 | 1999 Dodge Durango

4 Answers

1997 Dodge Caravan won't start - has a tick tick sound


Hi savvyuserbyo;

That tick, tick sound is probably the starter solenoid trying to activate the starter.

Here's a couple of things you can try. Take a hammer and tap the starter motor (not real hard, just medium) and then try to start it.

The 2nd thing you can do it to take a piece of wire, like lamp cord and(with someone helping) touch one end to the small terminal on the starter. (There is a large battery size wire connected to a large terminal on the starter, this is not the one you use) use the small terminal. Have your helper touch the other end to the positive terminal of the battery.

If the engine cranks. the solenoid is probably bad. If it doesnt crank the starter is bad.

The final thing to do is to remove the starter (after you disconnect the ground lead of the battery) and take it to an Auto Zone type store and have them check it out for you. BTW, starter and solenoid are sold as a unit. I just replace mine on my 94 F159 and is cost $100 exchange. If you need a replacement get a rebuilt rathert than a new. Just as good and cheaper.

Hope this helps Good Luck Loringh PS Please leave a rating if Appropriate. Thanks

Nov 23, 2008 | 1997 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...