Question about Audi Cars & Trucks

Open Question

P1768 code p1282 - Audi Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not start with out ,the code reader plugged in unplug the code reader and will stop gettig code p1768 and p0001


P0001 OBD-II Trouble Code: Fuel Volume Regulator Control Circuit/Open
Symptoms of a P0001 DTC will include MIL (Malfunction indicator lamp) illumination, although there may be other symptoms
If you get this DTC, you may want to try reading the codes using another (if possible) higher quality code reader. Even clear the code and see if the code comes back. This code is not common and sometimes is shown in error due to the design of the code reader (e.g. the code reader function is a secondary function of a tuner device).
P1768
Now with the code you said you had, P01768. DTC P1768 will set when TCM senses less than 3 volts at transmission control relay output (switched battery) terminals at TCM, prior to TCM energizing relay
Possible Cause
" Low battery voltage.
" Open fused B+ circuit to transmission control relay.
" Open ground circuit.
" Transmission control relay output circuit shorted to ground.
" Open transmission control relay circuit.
" Defective transmission control relay.
" Malfunctioning TCM. (very rare)

Sep 13, 2016 | 1999 Plymouth Voyager

1 Answer

How can you fix internal soleniod in a transmission?


go after the P1768 code first. sounds like trans relay is not sending power to the solenoid pack. check fuse #2 {should be a yellow 20 amp fuse} in underhood fuse/relay box. if it's blown it will cause all these codes. the relay is marked EATX and is in the same box as fuse. should be in one of the corners of the box. hope this helps, let me know

May 28, 2014 | 2000 Dodge Grand Caravan

1 Answer

Ver video de codigo p1768


the P1768 means "Performace/Normal/Winter Mode Input Malfunction"
_________________
TIS2000 software

Sep 07, 2012 | 2001 Dodge Caravan

1 Answer

Recently the transmission is Stuck in 3rd


P1768 - Performance / Normal / Winter Mode Input Malfunction

P1733 - 3-4 Shift Malfunction
I would suggest you have the shift solenoid electrically tested to determine if they are at fault here or that you have a wiring issue or a failed Transmission control module. You will need the help of a transmission shop to diagnose this properly, do not just replace parts until you are sure they are the problem.

Jun 18, 2012 | Jeep Grand Cherokee Cars & Trucks

1 Answer

What is a P1768 error code on honda accord 2000 model


just google honda DTC code P1768. you will get lot's of answers

Jul 27, 2011 | Honda Accord Cars & Trucks

1 Answer

I am getting a P1282 code.


that code comes from your fuel pump relay. Before you replace it, check to see if the contacts on the relay wires are dirty or corroded. If you clean them up and the code returns, it may be your fuel pump.

Aug 12, 2010 | 2000 Dodge Durango

1 Answer

P1282 code engine light is on. Just had leak detection pump replaced.


code 1282 is fuel pump/system relay control circuit.which means fuel pump relay has a problem, i would replace relay to fix this problem, but computer codes must be cleared . good luck hope this is helpful.

Oct 23, 2009 | 2002 Jeep Liberty

1 Answer

2001 dodge truck wont start


dear friend:code p1601 stands for engine control module(ecm)transmission control unit(tcm)-serial peripheral comminication malfunction,code p1282 stands for fuel pump relay-open circuit,fuelpump relay faulty and p1687 stands for metering oil pump-high flow-circuit malfunction,(wiring metering oil pump switch metering oil pump and ecm

Sep 22, 2009 | Cars & Trucks

1 Answer

CHRYSLER CONCORDE WITH DIAGNOSTIC CODES P1768 AND P1792


P1768 MEAN TRANSMISSION RELAY ALWAYS OFF..WAS UNABLE TO FIND P1792..IF PROBLEM STARTED AFTER HEADS WERE DONE..LOOK CLOSELY AT AT ENGINE MAIN WIRING CONNECTORS AND GROUND CONNECTIONS THAT ARE ON ENGINE..LOOK FOR GROUND EYELETS NOT SECURED OR LOOSE..LOOK FOR ANY PINCHED WIRING AS WELL..MAKE SURE NO SPREAD TERMINALS IN CONNECTORS AS WELL..YOU CAN ALSO TRY SWAPPING ANOTHER RELAY IN PLACE OF TRANS CONTROL RELAY..MAKE SURE PART NUMBERS MATCH UP..
TCM(NGC)PIN 16 IS TRS T3 SENSE CIRCUIT..PIN 17 IS NOT USED...HAS TO DO WITH TRANS RANGE SENSOR..I DON'T THINK THIS CAUSING YOUR PROBLEM..

Jul 30, 2009 | Chrysler 300M Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...