Question about Toyota Cars & Trucks

Open Question

2003 sequoia yaw rate sensor - Toyota Cars & Trucks

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: pls.where can i find the yaw rate sensor on 2001

Hello. Welcome to FixYa. The yaw rate sensor is attached to the steering column.

Posted on Oct 04, 2011


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is a yaw rate sensor & how does it affect braking?

This sensor detects a deviation of the vehicle from the centerline of the vehicle such as in a skid, the computer which is part of the skid control and abs system then adjusts the brake and throttle to pull the car out of the skid, the driver is not in control at that time until the vehicle skid is recovered, it is also a deceleration sensor. The yaw rate sensor does nothing under normal conditions

Jul 23, 2014 | 2003 Toyota Sequoia

1 Answer

How to remove steering column cover on 2003 Sequoia Toyota

what are you replacing? The YAW rate sensor? And why. are you have traction problems. Like your vsc lights coming on and your truck lossing control once applying brakes traveling at over 50mph? I had those same problems. If that's the case, tell me and i will be able to give you good advice.

Sep 05, 2013 | 2001 Toyota Sequoia

2 Answers

Pls.where can i find the yaw rate sensor on 2001 toyota sequoia?

Hello. Welcome to FixYa. The yaw rate sensor is attached to the steering column.

Oct 04, 2011 | 2001 Toyota Sequoia

3 Answers

Where is the yaw sensor located in 2003 lexus rx 300

Please see the diagram and yellow color highlighted part is the yaw rate sensor. 11_21_2012_5_47_14_pm.jpg

Apr 24, 2011 | Lexus RX 300 Cars & Trucks

1 Answer

2003 Toyota Sequoia - Brake light comes on during hot weather

your ecu got nothing to do with your brake,maybe your abs controller but i dont thing so,warping is basically couse of poor material or uses of exessesive brake,imagine your truck is big and heavy try not to setle with cheap rotors and good brake pad,after installing all new and break in and bedding it really good that should last u a 4 to 5 years before it warp again.check your sensor about the light check your safety brake sensor too..good luck

Dec 17, 2009 | 2003 Toyota Sequoia

1 Answer

My 2003 Toyota Sequoia's "Trac off" light, "VSC Trac" light and "abs" light all came when i turn the ignition on and didn't turn off any more.the dealer said got c1223 and c1244 code. how can this problem...

I had the same problem after I changed my brake pads. I found out later that it had nothing to do with the brakes. I had the codes on a piece of paper, but iI wound op throwing it away so I dont know if this is your exact problem. My problem was a part called a YAW RATE SENSOR . The part was about $500.00 including installation by an independent repair shop. Something else that I noticed was when you first start up and drive off, there are two small click sounds that are normal. After the warning lights came on, I did not hear those clicks. After the Yaw rate sensor was replaced, the clicks came back.

Oct 20, 2009 | 2003 Toyota Sequoia

4 Answers

2003 Toyota Sequoia 4WD

i have a 2003 sequoia ltd and i can tell you that the virtual traction control lights will come on after ignition and remain on as a result of anything that has affected your vehicle operation. from sensors to seals, the computer is designed to shut down the traction control if it has determined that any part of the engine/mechanical systems has malfunctioned. first it was the abs had to be reset after i slammed my brakes on. next i needed a new fuel/oxygen sensor, the passenger primary, and after having fixed both the traction control operates properly, lights go off after ignition and stay off. i think the vehicle operates more driver friendly when its off, because it doesn't go off every time one of the wheels slips. i expect it will happen next time something else malfunctions, its toyotas way of annoying you into their service shop. go to a tune-up shop, (minitune) instead they'll tell you whats wrong and it'll be cheaper.

Sep 11, 2008 | 2003 Toyota Sequoia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides