Question about 2002 Jeep Grand Cherokee

1 Answer

Bottom end knock

Could this just be shells and is access too fix them difficult thanks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

which engine, ?????
the main bearings, pound and make deep sound under heavy engine load. the rod bearings are LOAD RAP RAP sound, like hitting the block with a ball peen hammer.. so does no gasket on exh. flange.
why guess. there are easy tests to find cause.
and if you meant main bearings shells, that is :
1: if just shells, and no damage its 20hrs labor or more.
if crank bad, add $150 for a regrind of same and new bearings.
same for rods,

buy the FSM and read the engine overhaul section its all there.

see this page on noise the black art.
see methods , used, for engine noise.....

the noise can be isolsated by some tricks.

Posted on Nov 23, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2006 Stratus and the cigarette outlet has come unscrewed from the housing and I dont know how to get access to be able to screw it back in.

You have to access the cigarette lighter assembly from behind its mounting. The lighter is clamped in place by a round metal shell with threads. Twist the shell clockwise to tighten the lighter assembly.

Oct 21, 2013 | 2006 Dodge Stratus

1 Answer

How to open bonnet on 2003 toyota corrolla when cable release is broken

this is a lot easier said than done. the easiest way that i know and have done is gain access to the cable closest to the handle, this seems to be the most common place a cable breaks, the next would be at the latch itself. very rarely do the break in the middle. any way, gain access to the cable and cut it. once you have cut it peel off the plastic protective coating. after this is done it you should see the outer steel shell that houses the cable. most of these outer shells are not solid but more of a tight coil configuration. with a good pair of pliers you can "unravel" the outer shell to gain access to the inner cable. hold the outer cable with pliers and using another pair of pliers pull the inner cable and the hood latch should release. this is the easiest way to do it with out chewing your hands up

Mar 03, 2013 | Toyota Corolla Cars & Trucks

2 Answers

How do I fix frozen pipes in a motorhome

ouch.. sounds like it might be time for a trip to the repair shop.. there are ways to get to this... (has to be for repair purposes).. look very carefully.. you may have to remove covers, seats, flooring..walls.. etc.. very warm water will unfreeze your pipes..

Sep 20, 2017 | Cars & Trucks

1 Answer

2002 chevy prizm how to replace cig. lighter. do you have a how to video or other how to instructions??

Find the back of the cig lighter, pull the wire off. Then grasp the back of the device and turn (lefty loosey - righty tighty). You may have to hold the front (remove the lighter and hold its socket) to keep it from turning. There may be a ground wire on the shell (the part you are turning) that you will have to disconnect.

While the location may be difficult to access, the actual mechanics of the task are as simple as watching Ice Cream melt.

Thanks for your interest in

Mar 15, 2011 | Chevrolet Prizm Cars & Trucks

2 Answers

Lotus elise heater fan has stopped working. What is likely cause? And fix?

it is poor design on behalf of lotus the resistor pack that controls the fan is mounted externally below the fan unit and subsequently gets wet corrodes and fails. it is a difficult job not for the faint hearted and requires **** shell removal. There is a lotus mod released to fix this fault i would suggest using it prevent future trouble. Speak to a lotus dealer or specialist.

Nov 06, 2009 | 2005 Lotus Elise

1 Answer

How do I install front strut and spring conversion kit for my 1998 Cadillac Deville? Do I need to use a spring compressor? Thank you!

Yes, a spring compressor will allow you to compress the springs enough to remove the strut units. I recommend using the spring compressor that looks like a **** shell, not the ones that have the long bolt with the two clamps on each one. The **** shell type allows you better access to the spring bolts without interference.

Sep 13, 2009 | 1998 Cadillac DeVille

1 Answer

I have a '05 Ford Ranger. I bought a camper shell that has a Third Brake Light and I would like to hook it up so it works when I apply the brakes. Hooking the camper shell 3rd Brake lights to the p/u brake...

there will be four wires going to your lights you will have to test each wire to see which wire is for the brake light and tap into that wire. on all ford rangers one bulb controls everything so you can't just hook it up thru your bulb so you will have to hookit up thru your wires. it's not that difficult but you will have to have a helping hand. and test till you find the one for the brakes only.

Jun 09, 2009 | 2005 Ford Ranger

1 Answer

Removing/installing door components from/to door shell

sorry i cant tell u how to exactly howto take the old door apart NICELY without just having a light touch and the experience of doing other doors, but i would like to ask where u got ur door shell, i need one badly myself to and have had no luck so far finding one. any knowlage u have would be awsome, thanks

Mar 24, 2009 | 2003 Toyota Corolla

1 Answer


The cost of the sun shell is small about 40 bucks, labor will eat u up and other parts will likley be worn. Trans will have to be completely torn apart to fix,should consider a rebuild. My area averg. cost is $1600.00. Thank you very much.

Jan 05, 2009 | 2002 Chevrolet Suburban

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides