Question about Cars & Trucks

1 Answer

My truck will not start

Truck just clicks when i go to start. I took off starter, cut and fixed old wiring. Also checked fuses.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

What taking to the fixing place

Posted on Nov 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: 1998 ford f250 , starter won't engage

get under and hit starter with hammer a few times

Posted on Dec 21, 2008

  • 1118 Answers

SOURCE: 2003 Chevy S10 won't start

Are you sure its the starter? did you try it in neutral? could be park neutral switch, or ignition switch, or if its a standard shift maybe it has a switch on clutch that it has to be depressed to start and its bad. As far as jump starting you cross the maine or big post on starter to small or little post on starter to do that, on a v6 starter it on the right side under exhaust manafold, and i think its on the same side on a 4 cyl.

Posted on Feb 10, 2009

USfalcon
  • 175 Answers

SOURCE: 1999 nissan frontier truck won't start it just clicks

try to turn the headlight on and start if the light gose off at the same time you need to replace the battery , but if its stay on and no start change the starter

Posted on Mar 16, 2009

jturcotte
  • 8548 Answers

SOURCE: tryed to start truck and it would not crank. i

I'm assuming you have a no-crank condition. check interlock relay and safety interlock. Safety interlock is on shifter if you have automatic. It's on the clutch pedal arm if you have manual. Interlock relay should be in engine compartment relay box. You can bypass both of these and the ignition switch by jumping the solenoid. See troubleshooting procedures here: http://www.fixya.com/cars/r5821173-doesnt_car_start_gasoline_engines
and let me know if you have questions.

Posted on Sep 26, 2010

  • 228 Answers

SOURCE: when i turn the key

It is one of 2 things. Frist get undernesath the truck with a hammer and on the pass side you will be able to see the starter have someone hold the key in the crank postion and bang on the starter if that works then you need a starter. If not then check the big blue relay on the pass side fender wall in the engine compartment. It will look diffrent then any other relay becaus eit is a double connector and it is blue. You can not miss it.

Posted on Jul 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck wont start


the indications are that the battery is dead . have a load test done as the cells may have been damaged and are no longer operative.

Jan 12, 2014 | Cars & Trucks

1 Answer

2005 GMC Yukon XL will not start. Took starter off and had it tested. The starter is good. However, the PCM fuse is blowing when attempting to start truck or turning turning the switch to start the tr


There is a dead short to ground on that circuit . There are videos on youtube showing how to find an fix a short . Do you know how to do automotive electrical testing ? How to find automotive electrical shorts Look at the wiring harness under the hood for rubbed through wire's , harness going to the PCM , also find out what if any thing else is powered by that fuse . Which PCM fuse ? There are a few PCM 1 , PCM B , etc...

PCM 1 Fuse
15A
Powertrain Control Module (PCM), Mass Air Flow (MAF) Sensor, Evaporative Emission (EVAP) Canister Purge Solenoid, Fuel Composition Sensor, Secondary Fuel Pump Relay

PCM B Fuse
20A
Powertrain Control Module (PCM)

Any one of these fuse will cause the engine not to crank . The PCM energizes the starter relay which supply's power to the starter .

Mar 11, 2017 | 2005 GMC Yukon XL

1 Answer

Truck won't start key turns get a click out of fuse panel checked breaker good battery test good power going to panel not to starter checked wire off battery to starter good Is their another bre


make sure all grounds are clean and area of metal that ground wire's bolt to are clean and rust free if that check's out ok there could be a break in a wire going to the starter and most starter's have two wire's going to them and those both need to have power going to them one drop's off when key is turned to starting mode volt meter work's good for this or test light or the starter could be bad

Mar 04, 2012 | 2004 Ford F150

1 Answer

Truck was running day before, and every day before that, it was possibly -10 this morning and truck just clicked real fast, changed ground wires, battery to chassis to starter, and solenoid to transmission...


does the engine turn or does the start just engage when you say clicked real fast makes me think its the starter have you checked all fuses have you checked to see if its getting fuel is it getting fire from plugs

Dec 06, 2010 | 1984 Ford F 150

1 Answer

Truck ran fine shut off started 4hrs later would not click or anything. took out starter tested bad replaced starter ,new one does samething does not even click.


you have a master fuse in the truck under the hood in the fuse box the fuse should be about a 20 amp usually very big check this fuse to make sure that it has not blown.

Mar 28, 2010 | 2008 Dodge Ram Pickup 1500

1 Answer

Truck ran fine shut off started 4hrs later would not start


check your fuses/relays for starter,if both are good then check to see if the ground cable is connected to engine block. if that is good then remove starter and jump test to see if it is any good. u can still get a bad starter even if it is new.

Mar 28, 2010 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

Truck quit - was in fusable links-fixed one -truck started-cut it off-when try to restsrt no power anywhere-replaced all fuse links-hooked battery up -still no power anywhere


This used to be a common problem. Check to see that you didn't install the power feed wire for the truck on the wrong side of the starter relay. You should only have one wire on one large post. The one wire should be the one going to the starter. If any other wires are there they need to be moved to the other large post on the relay with the battery cable attached.

Dec 13, 2009 | 1989 Ford F 150

2 Answers

Truck turns over but wont start.. just replaced starter but ran prior to the old starter breaking down


Check the fuses. You may have blown one if you arched(saw sparks) the starter wires during removal and instalation.

Oct 27, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Ground problem


You probably have a bad ground. Check it at the starter and at the solonoid. usally just lossen and wiggle wires several times. then tighten. I found most of the fors are at the starter.

May 04, 2009 | 2005 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...