Question about Toyota Camry

1 Answer

Bad crank sensors symptoms

My sienna turn off when stop, after I run about one hour

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Check your crankshaft sensor

Posted on Jan 23, 2014

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
USfalcon
  • 175 Answers

SOURCE: crank sensor????

its look like to me bad cks even if its new one its happen some time
so change the cks and then reset the code and try have a good one
dont forget let me know what's going on

Posted on Mar 31, 2009

  • 17 Answers

SOURCE: What is symptom of a bad crank sensor. When I go

Usually when a crank sensor goes bad the car will not run at all, you can have an erratic reading that will cause your car to skip but will do it under any situation. Sounds like to me you have a problem with something in the
ignition system breaking down under a load. Could be a plug, wire, or coil.
depends on what engine you have. If it is a 3.8 liter the most common failure is the #1 spark plug wire, disconnect it and look at the ends, it they are corroded or look "rusty" you need to replace it. If so i would also replace the plug for that cylinder.

Posted on May 23, 2010

iambanshee74
  • 3489 Answers

SOURCE: engine will not crank, car just stopped running,

If there were no codes present upon initial inspection, check for fuel pressure and replace the pump if nothing or little is present. This is most likely with no codes. Also replace the filter. Let me know if you need instructions on pump replacement.

Posted on Oct 24, 2010

skychief2001
  • 21873 Answers

SOURCE: 97 geo tracker stops runing

If one of the sensors is failing, you should be getting a check engine light and a trouble code.
When you say it has fuel, do you have injector pulse and fuel pressure in the rail ?

Posted on Jul 19, 2013

Testimonial: "Pressure at the rail But didn't think to check injector pulse sense it runs extremely well until it gets warm. Trouble code now showing crank sensor. Had to replace O2 sensors first to get that one. Seems like I fix one thing just to find another. It's like a cascade and I don't get mutable codes so I have just been fixing one at a time. Thanks "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is my crank sensor faulty, symptoms of a faulty crank sensor 2000 Rodio 3.2 L


Intermittent stalling. Another symptom commonly associated with a problematic crankshaft position sensor is intermittent stalling. If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall.

Symptoms of a Bad Crankshaft Sensor ' DoItYourself.com

www.doityourself.com/stry/symptoms-of-a-bad-crankshaft-sensor
This makes it an important part of your engine system; a bad crankshaft sensor affects not only the engine speed but also the fuel efficiency of your car.

7 Crankshaft Position Sensor Failure Symptoms ' DoItYourself.com

www.doityourself.com/stry/7-crankshaft-position-sensor-failure-symptoms 1 - Check Engine Light. This can be frustrating as the check engine light can obviously turn on for many different things. 2 - Cylinder Misfiring. 3 - Acceleration Hesitation. 4 - Intermittent Starting. 5 - Engine Vibrations. 6 - Backfiring and Stalling. 7 - Irregular Car Function.

Warning Signs of a Bad Crankshaft Position Sensor ' DoItYourself.com

www.doityourself.com/stry/warning-signs-of-a-bad-crankshaft-position-sensor Ignoring the symptoms of a bad crankshaft position sensor will result in rapid wear and tear of the various parts of the engine and will quickly lead to engine ...

Symptoms of a Bad or Failing Crankshaft Position Sensor ...

https://www.yourmechanic.com/.../symptoms-of-a-bad-or-failing-crankshaft-position-... Jan 6, 2016 - Intermittent stalling. Another symptom commonly associated with a problematic crankshaft position sensor is intermittent stalling. If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. ‎Crankshaft sensor · ‎Car is stalling Inspection · ‎How Long Does a Crankshaft ...

Symptoms of a Bad Crankshaft Sensor - Buy Auto Parts

www.buyautoparts.com/howto/symptoms-of-a-bad-crankshaft-sensor.htm Problems you will run into when your crankshaft position sensor has gone bad.

symptoms of faulty crank sensor Google Search

Sep 22, 2017 | Cars & Trucks

1 Answer

First start any day is a nightmare. My 2000 toyota sienna hardly starts the first time i try to start. after going around, there is no problem starting. Any advice what is wrong?


Might be fuel pressure leakdown. Try turning the key to RUN for about 3-seconds, but not START. Then turn to OFF. Repeat 3 times and then try to start. If it starts, you have a bad check valve in the fuel pump that's allowing fuel pressure to drain down overnight. Replace fuel pump.

If that doesn't work, try depressing the gas pedal halfway while cranking the engine. If that helps, check out the engine coolant temp sensor. A sensor that's out of calibration will send bad info to the computer and the computer will provide too lean a mixture for a cold engine. Depressing the pedal overrides the sensor and the computer adds gas.

Aug 01, 2017 | 2000 Toyota Sienna

1 Answer

What are the bad crankshaft sensor symptoms on a 2005 toyota sienna


Failed crankshaft sensors will result in a no-run, cranks-but-wont-start condition.

Aug 02, 2014 | 2005 Toyota Sienna CE

2 Answers

2003 Accent crdi is run 10 kms and then all of sudden it stops and than if u crank several times it dont start. Try after an hour it will start , and again repet the same problam


clogged catalytic converter, classic example of what happens when they go bad. You have all the signs and symptoms. 98% sure its stopped up.

Dec 17, 2013 | Cars & Trucks

1 Answer

Erreur p0016 on sienna 2003 after change t-belt


The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.

The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0016 code will set.

Symptoms of a P0016 will or may include:
* Malfunction Indicator Lamp (MIL) illumination
* The engine may run but with reduced performance
* The engine may crank but not start
* The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged
* The engine may start and run, but poorly

Causes may include:
* Timing chain stretched, or timing belt skipped a tooth due to wear
* Misalignment of timing belt/chain
* Tone ring on crankshaft slipped/broken
* Tone ring on camshaft slipped/broken
* Bad crank sensor
* Bad cam sensor
* Damaged wiring to crank/cam sensor
* Timing belt/chain tensioner damaged

Possible Solutions:
1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Hope helps.

Dec 20, 2010 | 2003 Toyota Sienna

2 Answers

MY 95 jeep cherokee shuts itself down after about 3 mile going up a hill would it be the gear box 4l v6 it will shut off for about 4 hours then it will start again


Pretty sure they don't use a trans overheat switch on 95's What you are probably looking at is a crank sensor that is beginning to fail. I'd also check the fuel pump too as symptoms are very much the same except that right after shut down, if you turn the key back to run position, if the pump is bad, you won't hear it running. Best to get yourself a haynes or chilton manual so you can do the necessary testing. Crank sensor is the most common problem but cam sensor and coil can also give similar symptoms and because of that I don't ever recommending that you replace anything just because I think it may be bad Always test first. Parts are expensive!!!

Jul 12, 2010 | 1995 Jeep Cherokee

1 Answer

Cooling fan on 2004 Toyota Sienna doesn't stop running


What happens when you leave the relay out? Your fan control module may have a shott.

0996b43f802561b9-khhlhgabxhi45qdlqmlsiuhd-3-0.gif

Oct 30, 2017 | 2004 Toyota Sienna

1 Answer

My Toyota Sienna stays at 1000 rpms after completely coming to a stop at a stoplight and will move forward when i take my foot off the brake (on level surfaces). Also drives 15 - 25 miles per hour for 1/2...


If you have a CHECK ENGINE light on it is a bad sensor if there is no light check your floormat?? Sounds crazy but seen it before!!

Good luck hope this puts a stop to your problem!

Oct 23, 2009 | 2006 Toyota Sienna

1 Answer

1991 Buick Regal will not start


Chech to see if you're gettin a signal from the crankshaft position sensor located behind the crank pulley. If no signal, you have either a bad sensor or a bad crank pulley. There is a reluctor ring on the pulley that separates and goes bad. If you have a good square wave signal from the the crank sensor it's probably going to be the computer. I've replaced a lot of them. They do really wierd things when they start to go. Check all of your grounds first. Also, while the car is running, shake and pull on the wiring harnesses for the computer. I've seen on a few cars where a wire or 2 will go bad and cause and occational short.

Nov 06, 2008 | 1991 Buick Regal

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...