Question about 1992 Dodge Ram 150 Club Cab

1 Answer

Replaced crank sensor now ticking noise - 1992 Dodge Ram 150 Club Cab

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Dodge Expert
  • 652 Answers

The sensor not to correct deepth the air gap is not correct

Posted on Nov 21, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My 97 Jeep Grand Cherokee engine is ticking and tonight I barely made it home


I can't say what the noise is from this keyboard so please consult a local mechanic.

Jun 04, 2016 | 1997 Jeep Grand Cherokee

1 Answer

Replaced crank shaft ticking noise


There are a lot of steps involved in replacing a crank shaft where a simple mistake can cause problems. The bolts and end caps need to go back in the exact same position and direction facing the front. The crank needs to be stored upright or it can be damaged simply by its own weight while lying down. The bearings need to be the correct size and installed in the proper position lining oil holes up and greased properly. The bolts need to be torqued in the proper sequence and to the correct torque. The Crank then needs to be tapped with a hammer and torqued again.

Sounds like something was missed if your getting a bottom end engine noise now.

Nov 19, 2013 | Cars & Trucks

1 Answer

2003 dodge caravan 3.3l cranks but no spark have replaced timing chain my bad...but i have a clicking noise sounded like chain.....replaced crank sensor it had evidence of being smaked maybe causing my...


probably forgot to reinstall camshaft sensor which located on timing cover or forgot to reconnect camshaft sensor because crankshaft sensor and camshaft sensor work together to control fuel timing and spark timing.make sure ignition coil getting 12 volts.

Aug 11, 2013 | 2000 Dodge Grand Caravan

1 Answer

It sounds like a lifter i was told it was the harmonic balancer by several people i replaced it car stick making ticking noise and picks up speed slow


I am curious why they said harmonic balancer and you replaced it, there is a crank sensor near the harmonic balancer was it rattling or loose they have a tendency to get loose,the harmonic is the big main pulley when that breaks because it is vulcanized then yes it tick and your car looses power.You check sparkplugs for being loose and not being tighten up,check the air filter too,I am sticking with the Harmonic balancer this time remove the drive belt but dont do it too long or it will overheat just for 2 minutes maximum see if the noise goes away. 2 minutes only battery wont charge also

May 06, 2011 | 1998 Buick LeSabre

1 Answer

Feels like i have a dead cylinder


Throttle Position Sensor and NO you do not have to go to Ford and replace the whole Assy. The auto part stores have the sensor for about $70 and less on Amazon. The black smoke was unburnt fuel most likely from all the cranking and confused PCM and its imputs trying to determine fuel stratagy. Those noises are something you work on after you get the engine performance fixed. Don't throw parts at it. The TPS is just one possible cause,now you need to look for codes and then test for bad sensors etc. Codes alone don't tell you a part is bad. Code are set based on computer inputs out of range over a number of drive cycles or not seeing what a PCM should see while cranking.

Feb 06, 2010 | 2004 Ford F150

2 Answers

My 2005 stratus wont start turns over but doesnt start the trouble code is p0340 so i changed cam sensor and crank sensor still wnt start i need help so bad


2.4 L?REMOVE CAM SENSOR..CRANK ENGINE..MAKE SURE CAM IS TURNING..IF NOT..TIMING BELT IS BROKEN OR STRIPPED..NEW BELT SHOULD FIX PROBLEM..MAKE SURE YOU CHECK/REPLACE WATER PUMP/IDLER/TENSIONER

2.7L?REMOVE OIL FILL CAP AND SEE IF CHAIN IS MOVING..IF NOT..YOU HAVE COLLAPSED TENSIONER..YOU WILL HAVE SOME VALVE DAMAGE..LET ME KNOW IF TOU NEED MORE INFO

Dec 30, 2009 | 2005 Dodge Stratus

1 Answer

2004 Saturn Ion2 with 2.2L Has trouble accelerating up a hill or under hard acceleration. Also has Loud ticking noise (sounds like valves ticking). Check manifold vacuum with a vacuum gage and OBDII...


Sounds like a bad coil pack. If memory serves they had the double coil pack on the back of the motor that were notorious for going bad and were seriosuly cheap to replace.

I'd also be looking towards a CKP (Crank Position Sensor) in that car.

Nov 23, 2009 | Saturn Ion Cars & Trucks

1 Answer

Have a 2005 for f-150 started with ticking, knocking noise with no power. they changed the spark plugs did not help the truck is at Bickford Motor in Snohomish wash. they think it is the cam. do you have...


The ticking would be a bad valve lifter, bent or broken push rod
As far as the knocking, could be:
cam bearing, or cam
crank bearing
rod bearing
Might even be the knock sensor.

Jul 22, 2009 | 2005 Ford F-150

1 Answer

1997 Dodge Caravan won't start - has a tick tick sound


It sounds like the crank shaft sensor is hitting when you spin it over. It is probably in too far. There is a piece of card board stuck to the end of most of them to set it correctly. If it is not the the magnet will pull it to the metal reluctor. Pull it out and see if the end is rubbing. Then take a piece of card board from the box the sensor came in, put a dab of grease on the end of the sensor eg: magnet and put it back in, when it spins over the card board will be rubbed of. That should give you enough clearence for the magnetic sensor to work and not rub eg: the ticking noise.

May 30, 2009 | 1997 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...