Question about 2005 Chevrolet Monte Carlo

1 Answer

Bad back brakes

What tools is needed to repair back brakes disc on my car???

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,615 Answers

If your disks are bad, you need to replace them with new ones, or have them turned at a machine shop.

Posted on Nov 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing rear brakes on 2000 lincoln LS


You will need a special tool for the back brakes,Autozone will loan it to you for 60 bucks,you will get it back when you return,I used it.I replaced brake pads front and back and both back rotors.The driver side rear had metal on metal,all disc brakes,brake pads on that rear side were completely worn down to metal,the driver side was like new,kept wondering why,replaced both rear rotors,put back together,then then I noticed where brake line hose went into brake caliber was leaking,so that caused the side with new like brake pads not to be gripping disc putting all brake pressure of that one side,so the copper fitting their was bad,put new one on and leak stopped.

Aug 20, 2017 | Lincoln Cars & Trucks

1 Answer

How to Repair rear halshaft seal leaking onto brakes on 1998 mitsubishi l200


You will need to remove the complete wheel/brake assembly and possibly the backing plate to replace the seal on the shaft which is located outboard of the bearing. The seal is circular and pressed into a housing bolted to the backing plate. There are also gaskets at the backing plate (usually both sides) that will need to be replaced. A proper repair kit will contain everything necessary. If brake parts have been saturated in lubricant, THEY MUST BE REPLACED (brake shoes or disc pads). Consult a manual specific for your vehicle for the steps and tools you will need. Clean all parts with brake cleaner before reassembly and wear gloves.

Oct 03, 2014 | Cars & Trucks

1 Answer

Bad back brake pads


its a good idea to have rear disc caliper compressor. prob can get one from AutoZone (loan/rent)

Nov 19, 2013 | 2005 Chevrolet Monte Carlo

1 Answer

How do you replace rear drum brakes for 1994 Toyota Camry 4-clydr


See here for details, p37 or p44 depending on the car

http://www.turboninjas.com/camry/br.pdf


As to special tools, a can of brake cleaner spray (must be meant for brake parts), a pair of big strong pliers, a wire brush, and a set of metric spanners.

Aug 18, 2012 | 1994 Toyota Camry

1 Answer

What tools do i need too replace front brake pads on 99 olds alero


TOOLS YOU NEED TO REPLACE FRONT BRAKES YOU NEED A FLOOR JACK AND JACK STANDS.YOU NEED C - CLAMP TO COMPRESS CALIPER PISTON IN ITS BORE. SO THE BRAKE SHOES IN CALIPER WILL FIT OVER THE DISC OR ROTOR.YOU NEED A SIPHON OR LARGE SYRINGE TO REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER RESERVOIR SO WHEN YOU COMPRESS CALIPER PISTON BRAKE FLUID WONT SPILL OVER MAKE A MESS POSSIBLE DAMAGE CAR PAINT.SHOULD AVOID GET IT ON YOUR HANDS ALSO.YOU NEED A 3/8 RATCHET AND SOCKET SET.ITS ALSO GOOD TO HAVE A HAYNES OR CHILTON REPAIR MANUAL.IT WILL GUIDE YOU THROUGH THE PROCESS.BESURE WHEN YOU FINISH PUTTING ON BRAKE PADS.PUMP UP BRAKES WITH BRAKE PEDAL UNTIL THEY ARE FIRM.MAKE SURE YOU PUT BACK ON MASTER CYLINDER COVER BEFORE PUMPING UP BRAKES.AFTER PUMPING UP BRAKES TO SEAT BRAKE PADS AGAINST ROTOR CHECK BRAKE FLUID LEVEL.

Feb 22, 2010 | 1999 Oldsmobile Alero

2 Answers

Are there any special tools needed to change the brakes on a 2006 toyota sienna? Standard two bolts that hold it on?


You will probably not need anything other than a metric socket wrench set.

Many Toyota models have disc brake calipers that will flip up or down when you remove one of the two bolts that hold the calipers on. I am not sure of the setup on the Sienna.

When you remove either the upper or lower bolt and move the caliper, you can then remove the old pads. Also, you will need to push the piston(s) back into their cylinders to give you enough space to install the new pads. A large C clamp will usually suffice to push in the pistons.

I assume that you are talking about the front (disc) brakes. Some autos still have drum brakes on the rear, and those are a different story. They require several specialty tools to remove and replace the shoes.

Oct 11, 2009 | 2006 Toyota Sienna

2 Answers

Is there any special tools to change the brakes on a 2000 lincoln ls


standard hand tools, remember to have the rotors turned by a machine shop.

May 26, 2009 | 2000 Lincoln LS

1 Answer

Replacing disc brakes on a 2000 v.w jetta


When I changed my sisters VW Jetta I used the follow:
  1. Lug Wrench
  2. Ratchet
  3. Socket to fit the caliper bolts (can't remember size)
  4. C-Clamp to push the piston back in
  5. Bucket to set the caliper on while changing the pads
On the rear brakes I had to borrow the special tool to push in rear disc brakes from AutoZone, this tool spins the piston while pushing it back in.  Let me know if you have any other questions.  Thanks for an honest rating and thanks for using FixYa!

May 19, 2009 | 2001 Volkswagen Golf

1 Answer

Need to replace Discs and left rear rotor, what tools are needed?


Once the wheels are off you will need metric sockets and possibly metric wrenches.I believe the sizes are 10mm in rear to get the calipers off and 13mm in front. but have a range of metric sockets available. You will also need a c-clamp or large channel lock pliers to compress the caliper piston back into the caliper on the front and rear befoer installing the new brake pads and caliper back onto the vehicle.
Good luck with the repair.

Apr 20, 2009 | Jeep Grand Cherokee Cars & Trucks

4 Answers

2002 Jetta Brakes


On one of the front driver side pads there is a sensor for low pads. He either did not hook it back up or got a lose connection to it.

May 29, 2008 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
2005 Chevrolet Monte Carlo Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...