Question about Honda Accord

1 Answer

Multifunction switch 1 headlight turns off and wipers run when light switch is turned on.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

No year, stated, sigh.

Posted on Nov 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 206 Answers

SOURCE: 2008 wrangler 4 door. windshield wipers are stuck

2008 should be under warranty, take it back to dealer.

With all of the electronics on vehicles today, seems like these sort of system failures are becoming commonplace.

Posted on Sep 24, 2009

ndguy2481
  • 251 Answers

SOURCE: Replace multifunction switch on Pontiac Gran Prix 2000

no just the top and bottom of the steering wheel cover

Posted on Dec 07, 2008

emissionwiz
  • 78919 Answers

SOURCE: Turning off DRL.. 97 Monte Carlo

You will need to remove the DRL module then headlights will operate normally.

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: Headlights won't turn on. Daytime running lights stay on.

My 2002 S10 had the same problem, I pulled off the bottom of the dashboard and bottom of the steering wheel cover (around 8 bolts). There's a plug on the left side behind the cruise control/high beam stalk with several wires attached to it. Turns out some of the wires had become brittle and moving the steering wheel up and down caused them to short. The four small wires for the cruise control all broke off. I pulled out the metal pins and reattached them to the wires, worked for a while...

Posted on Oct 07, 2009

  • 2 Answers

SOURCE: 1997 dodge caravan se 6cyl 3.3

I think you need to replace the Body Control Module (BCM), My newly replaced BCM (used) fixed my wiper problem but created a new problem which the left turn signal is not working now. Time to sell the van.

Posted on May 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What can i do to fix a short in wiring to my wipers and headlights?


u need a repair manual--parts store hasum--ur library sec629 -automotive -if it seems more then u can handle--get a specialist

Nov 27, 2011 | 2000 Plymouth Breeze

2 Answers

My windshield wipers will not turn off and I have no turn signals.


I think your combination switch is malfunctioning. The switches that control both the wipers and the
turn signals are built into the combination switch. And the headlight controls too on some cars.

Your car may have a switch that controls the wipers and the turn signals, but not the headlights.

But whether you have the type that controls wipers/turn signals/headlights or just turn signals/wipers Im not sure, you didnt mention the specific year and model. But you should replace the switch that controls your wipers/signals. They are expensive sometimes, especially if you have the combo switch that controls wipers, headlights and turn signals. But you can find one at a slavage yard for a lot less money than new.


But you should put the year/model of your car when you post a problem youre having. That makes it more likely that someone can help.

Sep 10, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

No brake light,no turn signals , no flasher lights...I have checked fuses for each and they are OK. Also all bulbs are OK. Any suggestions.


Hi!!
Your multifunction switch may be defective. Replace it. $39.99 at AutoZone
  • Combination switches operate wipers, directionals, horn, headlights and dimmers.
  • When not replaced, wipers, directionals, horn, headlights and dimmer, independently or as a group, will not function or turn off potentially causing safety issues.
1kbron_136.jpg
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Apr 02, 2011 | 1996 Ford Thunderbird LX

3 Answers

I have a 95 mustang. headlights turn on but will turn themselves off when driving lol no fun at night! have to hold my brights?


First off do you have factory lights or the aftermaket high intensity bulbs. if you do get rid of them and replace them and your multifunction switch (headlight signal light high beam wiper switch)

Mar 21, 2011 | 1995 Ford Mustang

2 Answers

Wipers don't work on intermittent. They run but stop in they middle of the windshield and don't go to the bottom like normal, Then they run again and stop some other spot. When put on continuous they...


Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper RUN/PARK relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect senses magnet to turn off RUN/PARK sense the output to the windshield wiper RUN/PARK software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.

  • The intermittent windshield wiper speed does not operate correctly
  • Multifunction switch.
  • Circuitry.
  • Windshield wiper motor.
  • Go To Pinpoint Test D .

Pinpoint Test D: The Intermittent Windshield Wiper Speed Does Not Operate Correctly
Normal Operation During normal operation, the windshield wiper motor receives voltage at all times through battery junction box (BJB) fuse 1 (30A), circuit 65 (DG). The windshield wiper motor also receives power with the ignition switch in RUN or ACC positions through central junction box (CJB) fuse 33 (15A), circuit 1002 (BK/PK). Ground is provided to the windshield wiper motor through circuit 676 (PK/OG) and circuit 57 (BK). The run/park and high/low relays are contained in the wiper motor electronics. Mode of operation is dependant on the signal(s) received from the multifunction switch.
    Possible Causes
  • Multifunction switch
  • Open in circuit 57 (BK), 56 (DB/OG), 61 (YE/RD) or 63 (RD)
  • Windshield wiper motor
PINPOINT TEST D: THE INTERMITTENT WINDSHIELD WIPER SPEED DOES NOT OPERATE CORRECTLY Test Step Result / Action to Take D1 CHECK THE MULTIFUNCTION SWITCH
  • Key in OFF position.
  • Disconnect: Multifunction Switch C202b.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to D2 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . TEST the system for normal operation. D2 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between multifunction switch C202b-6, circuit 57 (BK), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes
GO to D3 .

No
REPAIR the circuit. TEST the system for normal operation. D3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD) AND 63 (RD) FOR OPENS
  • Disconnect: Windshield Wiper Motor C125.
  • Using the following table, measure the resistance between multifunction switch C202b harness side and windshield wiper motor C125 harness side:

    Multifunction Switch C202b Windshield Wiper Motor C125 Pin 2, circuit 56 (DB/OG) Pin 10, circuit 56 (DB/OG) Pin 4, circuit 61 (YE/RD) Pin 1, circuit 61 (YE/RD) Pin 1, circuit 63 (RD) Pin 9, circuit 63 (RD) Pin 3, circuit 58 (WH) Pin 11, circuit 58 (WH)
  • Is the resistance less than 5 ohms?
Yes
GO to D4 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. D4 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to D5 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. D5 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as outlined in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by incorrect binding pivot arm adjustment. REFER to Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

Feb 19, 2018 | 2006 Ford F 350 Super Duty

1 Answer

I have no brake lights, the blinkers run really fast and if the headlights are on the blinkers will not run at all while braking. Any ideas?


Have the multi-function switch and its circuits tested. The multi function switch is the blinker arm and the components its attached to in the steering wheel column. The multifunction switch has to do with blinkers, cruise control, wipers, wiper spray, high beams and also tied in with headlight dimmers/daytime running lights(if applicable) and hazards usually.

A good place to start.

Apr 26, 2010 | 2001 Chevrolet Silverado 2500HD

2 Answers

Turn signals quit working??


Good place to start is to check bulbs. Also, have multifunction switch and its circuits tested. The multifunction switch is the blinker arm, and the components it attaches to inside the steering column. Usually tied in with things like high beams, headlight dimmer/daytime running lights, wipers, cruise, etc.

Apr 26, 2010 | 2002 Volkswagen Beetle Turbo S

1 Answer

My dash lights all go out when i try and put the turn signal on. which arnt working either. car runs fine otherwise.


Your turn signal switch is multifunctioning (controls cuise, wipers, dimmer, etc.). Your dash lights are wired into the same circuit (when you turn your headlights on, the dash lights should come on). Try replacing the turn signal switch there at your steering column. Takes about 20 minutes to install and around $60.

Jun 08, 2009 | 1992 Dodge Caravan

1 Answer

94 Suburban headlight and turn signal problems


Sure they did your multifunction switch is the wipers and turn signal and hi low beam switch your headlights have to run through that switch also so you can dim or brighten them

Nov 20, 2017 | 1994 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...