Question about 1993 Jeep Grand Cherokee

Open Question

Have a '93 jeep grand cherokee

While replacing bad female pins the jeep started once, then when the wires were pushed back to a bundle size the jeep stopped working. I think the new pins, being correct ID ok, but the body of the pins allowed shorting.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: 93 Jeep Grand Cherokee Laredo

Could be a sensor.I'm thinking more along the lines of a fuel pump or fuel filter.If the fuel pump is going bad..similar symptoms.Would be advisable to install a pressure gauge at the engine,and check fuel pressure when it's acting up.

Posted on Jul 14, 2008

Ad
Mike258
  • 1498 Answers

SOURCE: 2000 Jeep Grand Cherokee Limited

Hey there Dave,

Had the same thing happen to my Wrangler about three years ago.
It was the weep hole too.

I drained the coolant, dried the weep hole and plugged it with a small amount of that solid epoxy they market to fix holes in gas tanks. I refilled the radiator and the plug held.

It's still holding.
Just an alternative option

Mike

Posted on Nov 26, 2008

Mikey108
  • 475 Answers

SOURCE: 2002 Jeep Grand Cherokee Lardo misfiring

You say you changed the cam sensor. A1391 code is a crank sensor on the top of the trans. bell housing.

Posted on Feb 24, 2009

  • 50 Answers

SOURCE: 93 Jeep Grand Cherokee Won't start

The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.

Posted on Apr 15, 2009

  • 11 Answers

SOURCE: where is the fuel pump relay located at on a 93 jeep cherokee

its in the fuse box under the hood

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 93 jeep grand cherokee 4x4 it is starting to hop when turning


It's the gears in the front diff. that are bad. You will need to replace those gears or the entire front solid axle.

Mar 14, 2013 | 1993 Jeep Grand Cherokee

1 Answer

93 jeep Cherokee wont start


Could be a crank or cam sensor gone bad. I suggest you get a haynes or chilton manual and do the testing outlined in them to determine which it is. Neither item is very inexpensive and the crank sensor is a real pain to replace. There are other things that can do that so testing is important.
Crank sensor is the most common failure but asd relay, wiring problems, bad ground on a relay etc can do much the same thing.
Anything you find that you need further help with I'll be happy to answer if I can!
Good Luck!

Apr 17, 2010 | 1993 Jeep Grand Cherokee

1 Answer

How to replace window regulator on 1999 jeep grand cherokee passenger side front


sorry I don't have much on this one. But, once the door panel is removed, you need to disconnect the glass from the regulator. I can't remember... but I think it is held on with U clips. They are just pushed in on the back side of the trolly. Too release them just push to one side. (see pic)
2218041.jpg *****NOTE: this is from another vehicle but the pin is the same...in the pic. the pin is being pushed back into place.

push the glass all the way to the top of the door and tape it there. Unplug the motor, unbolt the regulator and remove.

4803164.jpg (Im pretty sure that year had 2 pins to hold in the door glass, if I'm wrong you will clearly see 2 X 10mm bolts holding the glass to the regulator)
hope this helps.

Nov 22, 2009 | 1999 Jeep Grand Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

1 Answer

93 jeep grand cherokee 4.0 L wont start.


start by tracing the wires back to the computer checking for breaks in the wire or corroded terminals

Mar 23, 2009 | 1993 Jeep Grand Cherokee

1 Answer

93 Jeep Grand Cherokee Laredo


Could be a sensor.I'm thinking more along the lines of a fuel pump or fuel filter.If the fuel pump is going bad..similar symptoms.Would be advisable to install a pressure gauge at the engine,and check fuel pressure when it's acting up.

Jul 13, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...