Question about 2010 Renault Grand Scenic

Open Question

Location of airbag module

Cant find wires for the module

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the airbag light to go off on a 2007 Chevy van Express


You need to find out what code or codes are stored in the airbag control module > There are a lot of components involved in your airbag system : If you haven't had any training on these systems your best bet is take it to a ASE certified repair shop . People have been killed messing with these systems not knowing what they were doing .
The frontal SIR system consists of the following components:
?€¢
AIR BAG indicator located on the instrument panel cluster (IPC)


?€¢
Driver and passenger knee bolsters


?€¢
Inflatable restraint front end sensor


?€¢
Inflatable restraint PASSENGER AIR BAG ON/OFF indicator located on the instrument panel


?€¢
Inflatable restraint Passenger Presence System (PPS)


?€¢
Inflatable restraint I/P module


?€¢
Inflatable restraint I/P module disable switch


?€¢
Inflatable restraint seat position sensors (SPS) (left/right)


?€¢
Inflatable restraint sensing and diagnostic module (SDM)


?€¢
Inflatable restraint steering wheel module


?€¢
Inflatable restraint steering wheel module coil


?€¢
Inflatable restraint wiring harnesses


?€¢
Seat belt pretensioners (left/right)


?€¢
Steering wheel and column

Nov 22, 2015 | Cars & Trucks

1 Answer

LOCATION OF AIRBAG CONTROL MODULE THX


How To: Remove SRS Airbag Computer Control Module ...

? 5:12
https://www.youtube.com/watch?v=kPduYbtAYds
Jun 23, 2012 - Uploaded by Charley O'Neill
This video will show you how to locate and remove airbag control ... How To: Remove SRS Airbag Computer ...Missing: thx

how to know or diagnose airbag SRS air bag control module ...

? 4:55
www.youtube.com/watch?v=2MdTkmk4FiQ
Feb 3, 2010 - Uploaded by vehix411 http://karmanauto.com/product/honda-and-acura-airbag-module-reset- ... will show you how to reset and or ...

Oct 30, 2015 | 2007 Toyota Tacoma

1 Answer

WHAT IS P1801 ERROR


drivers level 1 airbag igniter open circuit

If airbag light on dashboard is ON, in most cases there is a problem with ribbon cable located in "COM2000" module. When you remove airbag, look at the BLUE connector to see if wires are connected. Rather complicated repair for DIY. Best to find working used complete module.

Aug 16, 2014 | Peugeot 206 Cars & Trucks

1 Answer

Electrical starting problem, 1988n ford f150 4.9 ltr. I keep getting secondary Ignition. I brunt one starter out already changed it & the starter relay switch , checked ignition switch [o.k], checked...


use ohm meter to check ground to pos cable to starter If 000 check for ground wire on starter it should go to starter bolt. voltage reg stuck open Unplug ignition module check battery if still sparking not module.

Dec 29, 2013 | 1988 Ford F 150

1 Answer

P0605


You'll probably need a mechanic for this.
Code 605 is for a problem with the ignition module. The module fires the coil. The module and wiring would need to be tested.

Jun 09, 2013 | 2002 Chrysler Sebring

1 Answer

How would you hotwire a Mazda b2300 if u lost the key.


cant hotwire your vechicle has the PATS SYSTEM.your keys has transponder on it.the ignition switch antenna ring and immobilizer control module and ECM read signal emitted from the keys transponder if you have no keys or wrong keys the PATS SECURITY SYSTEM DISABLE IGNITION SYSTEM CAR WONT CRANK.CANT HOT WIRE CAR WITH THE PASS KEY SECURITY SYSTEM.older cars back in 70s you could hot wire newer cars you cant.

Apr 05, 2013 | Cars & Trucks

2 Answers

Cant find ignition module in 2001 pontiac grand am


its underneath the coil packs where your spark plug wires run from remove coils to get to it

Oct 20, 2012 | 2001 Pontiac Grand Am

1 Answer

I want to replace the right hand speed control for the cruise control on my 2008 Chrysler Aspen - any ideas? Anyone!


11_18_2011_12_24_34_am.gif
REPLACING CRUISE CONTROL SWITCH

1.
Disconnect and isolate negative battery cable from battery.

2. Remove airbag module (See AIRBAG REMOVAL below).

3. Remove speed control switch mounting screw and remove switch from steering wheel.

4. Reverse procedure to install.
AIRBAG REMOVAL
1. Disconnect and isolate negative battery cable from battery.

2. From the underside of the steering wheel, remove the two screws that secure the driver airbag to the steering wheel armature.
CAUTION: The horn switch and the clockspring pigtails connected to the back of the airbag module are fragile. Do not pull on these wires to disengage them. These must be handled carefully to prevent damage to the horn switch and/or the clockspring assembly.
3. Pull the driver airbag away from the steering wheel enough to access the three electrical connections on the back of the airbag housing.

4. Disconnect the steering wheel wire harness connector for the horn switch from the horn switch feed pigtail wire connector, which is located on the back of the driver airbag housing.

5. The clockspring driver airbag pigtail wire connectors are secured by integral latches to the airbag inflator connector receptacles, which are located on the back of the driver airbag housing. Depress the latches on each side of the connector insulator and pull the insulators straight out from the airbag inflator to disconnect them from the receptacles.

6. Remove the driver airbag from the steering wheel.

7. Reverse procedure to install.

Nov 17, 2011 | Cars & Trucks

Not finding what you are looking for?
2010 Renault Grand Scenic Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

xxxxxx xxx

Level 3 Expert

4874 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...