Question about Cars & Trucks

Open Question

Freelander td4 p1260

Car imobilised fault code p1260

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22326 Answers

SOURCE: reset fault code on 1996 jaguar x300

dealer only sorry

Posted on Dec 10, 2008

Ad
  • 61 Answers

SOURCE: freelander td4 power loss at 70mph

yeah, don't drive so fast!!!!...seriously i would do what has to be done anyway to start. change fuel filter, air filter, spark plugs, spark plug wires. these have to be done at some point if they haven't been.. if that solves your problem, if not look at fuel pump, injectors.u didn't say if it used to go faster, maybe there is a limiter.

Posted on Jul 24, 2009

  • 2 Answers

SOURCE: Low Fuel Pressure on Landrover Freelander TD4

From 53 reg onwards, diesel pump is under R.H. rear wheel arch, hidden by the plastic wheel arch liner. Older versions have combined fuel pump/sender in the tank (under R.H part of rear seat).
You should be able to hear a faint purr from the pump when ignition is turned on but engine not yet running.

Posted on Nov 15, 2009

  • 1 Answer

SOURCE: freelander td4 wont start

I have exactly the same issue!

Posted on Jan 28, 2010

  • 20 Answers

SOURCE: starting problem freelander td4

have you change plugs and fuel filter

Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1260 code detected on my 99 xj8 jag how do I fix


code p 1260 refers to vehicle immobil;izer invalid ignition key/immobilizer system fault
try using the scan tool to reset the ECM or talk with a dealer service center for the immobilizer problem
make sure that the battery in the key fob is fully charged if it just happened

May 12, 2017 | Cars & Trucks

1 Answer

I have a 2003 S-type jaguar that goes into a limp mode and stops running then the engine system fault shows ,the parkbrake fault and DSC not available also shows. Diagnostic showed codes PO121,P1582??


code p 0121 is associated with the throttle position sensor and accelerator position sensor
causes are from cable adjustment --throttle position and accelerator position sensors
code p0533 refers to ac refrigerant pressure sensor--high input== causes --ac pressure too high (cooling fault -condenser fan not running at radiator-- too much gas --pressure sensor
p 0105 refers to map sensor / barometric pressure sensor --circuit malfunction===causes wiring--- map sensor --baro sensor ECM
code p0566 refers to cruise control master switch== causes --control switch , ---ECM
code p1582 refers to electronic throttle monitor data available which will be associated with the p 0121 code and faults

Jan 08, 2017 | Jaguar Cars & Trucks

1 Answer

I have a 1998 taurus sho 3.4 has a code p1260. But it will start how do I get the code off


fix the fault shown and then use a scan tool to reset the ECM
if you don't fix the problem it will be back with in minutes

Dec 17, 2015 | Cars & Trucks

1 Answer

P1260 immobilizer system detects that engine startup disabled


Clear immobilizer code P1260. Cycle key 2 times and start the engine.

Nov 26, 2013 | 2004 Mazda 3

1 Answer

Fault codes I have on my bmw x5 2003 is p3505 p1260 p09f6 what do I need to fix them


P1260 is pre supply pressure monitoring, rate reduction due to low-pre-supply pressure. That is, fuel related. However, this normally triggers limp mode (<30mph/<2000RPM). Not uncommon on the X5. I would start with replacing fuel filter before delving into the lift pump/fuel delivery unit, in tank pump etc. Clear fault codes, run the car again then see what happens again - same fault codes?...then its delivery fuel pressure related. Should be 3.9bar at idle and not drop below 3.5bar.

Nov 04, 2013 | Cars & Trucks

1 Answer

P1260 code


It's gone into "limp home mode"

Oct 05, 2013 | 2000 Saab 9-3 Viggen

1 Answer

Freelander TD4 2005 Smoke


check for correct turbo operation
run the fault codes

Feb 21, 2018 | Land Rover Freelander Cars & Trucks

1 Answer

Hi my Saab 2001 93 2.0 turbo convertible has lost power get into limp home mode I reset it every few weeks codes come up p1105 p1260 p1251 p 1264 what do u think is wrong ?


code p1105 refers to manifold absolute pressure(MAP) sensor, TC system-leak detected. causes ---intake leak, ---hoses There are to references to p1105 The second response is still map sensor but the causes are---TC system--mechanical fault--air leak between throttle body-TC,map sensor---TC system--exhaust blockage
code p1260 refers to throttle return spring--weak spring force. causes ---mechanical fault,--,throttle control unit
code p1264 refers to throttle valve opening-accelerator released causes ---throttle control unit---mechanical fault

Mar 28, 2013 | 2001 Saab 9-3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13632 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...