Question about Cars & Trucks

Open Question

C20xe astra, fan working but still overheating

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If there is an overheating problem in Holden Astra diesel, does a dashboard indication come on. 2007


There should be a warning light to inform you of a fault however it will depend on what is at fault. What is happening is there steam/coolant level dropping/ fans running all the time. Can you explain in more detail?.

May 27, 2017 | Holden Cars & Trucks

1 Answer

My opel astra estate 160i,1995 model radiator fan not working


Hi, there are a few things that are the usual suspects,ill try to walk you through what and how to check. First, you need to check your coolant for circulation and overheating. When the vehicle is cool, pop the head take off the radiator cap,check and see if you have coolant. If yes,start the vehicle and let it get warm. Watch in the radiator top to see if coolant is flowing. If not,your probably overheating due to your radiator is dirty or a water pump issue. If it flowing, we need to check the electronic issues. To do this you'll need a meter or a test light, and a piece of wire. If you have a meter,unplug the fan plug set your meter on ohms and see which one is ground. You do this by turning off the ignition. Replug the connector loosely so you can access the terminals,take your meter and put one end to ground the other to the connector, the one that pegs is your ground. Take your wire put it on the other terminal the other end of the wire to the pos. of the batt ,the fan should kick on. If not your fan motor is bad. From this point, you'll have one of three issues. The fan/temp sensor is def. The fan relay is def, or a wire is def. Hope that helps.

Oct 28, 2016 | Opel Astra Cars & Trucks

1 Answer

I Have a Daewoo lanos 1.6 will a C20XE motor fit to the gearbox? If not, what engine will work as replacement engine


Use ONLY exactly the same stock engine as is in it now. Try and install a different engine and you will have mega problems with the electronics.

Nov 27, 2015 | 2002 Daewoo Lanos

3 Answers

I have Opel Astra 18ie it has a problem with overheating I have changed water pump ,radiator,skimmed the top and the engine block but still has overheating problem


i think since u have skimmed the head and the block u should check the tightness or tocks of the head bolts and retock if necessary

Mar 07, 2015 | Opel Astra Cars & Trucks

1 Answer

Vauxhall astra 1.7 code fault ecn 189554 going into limp mode


P1895 = Limp home mode - Limited performance
P1481 = Fan Control Circuit 1 - Open Circuit
P1482 = Fan Control Circuit 2 - Open Circuit

it could be there is an issue with the cooling fans on the vehicle, and the ECU is going into limp mode to prevent the engine overheating, or because the coolant temp is getting too high.

First, check all fuses are present and not blown.

Aug 28, 2013 | Cars & Trucks

1 Answer

Radiator fan not working


have you checked fan relay or fuse in fuse box or may be may be brekage in wire

Jul 31, 2012 | Vauxhall Astra Cars & Trucks

1 Answer

Fan belt diagram 1993 Opel astra


if you go to google it should tell you what it is.. you would have to type in the year model and type of vehical and also the type of motor

Jun 18, 2012 | Opel Astra Cars & Trucks

2 Answers

I have a 1998 Holden Astra eng noEL20B24119 and want to know the Head bolt torque settings and sequence. The engine is the transition model with twin tappet cover seals. has the torx star headed bolts.


I cannot find a EL20B in my data,but all Astra listed had the same head sequence as shown:

10 6 2 3 7

9 5 1 4 8

the torque specs for the C20XE,C20NE,X20XEV were all
25nm(18lb/ft),-then 90 deg,-90deg,-90deg.
Z20LET were as above plus an additional 15deg.
Same data for smaller and larger engines(except a couple that were 45deg instead of 15)
Make sure that you replace the head bolts with new,they are torque to yield bolts that are designed to stretch to 'plastic' state,and should not be reused.
Put grease(graphite if you have it) under bolt heads and washers,oil the threads.
Usually the head sets come with the torque specs.
I hope this helps you.

Apr 02, 2011 | Honda Accord Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...