Need settings for big ends and cylinder head fiat strada 1600 16v 2008 model

Question edited for clarity and put in spaces and CAPS.

About half a day to 6 hours. You will either have to get the pipe made, or buy it pre-made. The pipe ends are flared with nuts in place.

https://www.google.com/search?q=2010+Fiat+Strada+Bakkie+1.4.+replace+clutch+master+cylinder+and+slave+cylinder

..

not much on it apart from in the forums. They are normally under the engine fuse box or up under the dash on the drivers side.

https://www.google.com/search?q=2008+fiat+strada+el+ecm+location

..

No COUNTRY TOLD at all , SOUTH AFRICA?

it's in the manual buy it?
is it turbo?
no country told
some engines made in some countries for FIAT are not the same..
learn to get the correct manual for you car.
2008 Fiat Strada 1.6L
and country, even learn the real name for the engine and 1.6L
is NOT IT.

Powertrain

1.6 L Torque I4 petrol 1969 to 2010
1.6 L E.torQ I4 flexyfuel

#1 is my guess 41 years it evolved, just this engine.
1.6 Torque MPI EL, 1.6 Torque MPI EL < in Africa, it tells wiki
some are turbocharged, opted
and most engines made for that run a special block
and very different torques and pistons and rods ,all forged.

the blocks have codes telling what it is.
seen here for sure 6 block codes 2008

https://en.wikipedia.org/wiki/Fiat_128_SOHC_engine


buy the shop manual for exact car or exact engine.
and read it.

On most vehicles there is a release button at the bottom of the headrest 'legs'. I think on the Strada it is two push in buttons, one on each leg, on the plastic hole the headrest slots into.
Try this web page for the owners manual for the Fiat Strada.

https://www.manualslib.com/manual/1816555/Fiat-Strada.html?page=20#manual

http://www.speedwayautoparts.com/index35.htm

follow link got to torque table and look up your vehicle

This site should have the torque settings.

http://www.championbrands.com/aera-torquespecs.pdf

Not sure where you are, friend, but my data book tells me the Fiat Strada was produced in the 1980's and there wasn't a 1.2 model, a 1.1 and a 1.3 is what appears in the book.

I remember the car quite well as I worked on a few, typically the car was short-lived due to the severe rate of body corrosion.

If your car is a locally made under licence in the way of many of the eastern bloc Fiats, you will need to obtain technical information locally as in those circumstances made under licence cars rarely used the original engines.

It is also possible your car is not a Strada at all but maybe something like a Fiat Bravo that is locally named a Strada because another manufacturer is already using the Bravo name or perhaps the original name clashed with a slightly distasteful product. The Strada was originally the Ritmo but had to be named Strada in the USA due to a similar sounding brand of sanitary towels.

Try this link for the torque settings.

http://www.championbrands.com/aera-torquespecs.pdf

https://www.google.com/search?q=Engine+diagram+92+geo+storm+gsi&biw=1362&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwjYzZrkhpjQAhWBfCYKHd5eCVMQsAQIGg#tbm=isch&q=Need+torque+settings+fir+vw+polo+2008+1.6i+8+valve.+...+cylinder+head+mains+and+big+ends+
Hope this helps

http://www.fiatforum.com/tech-talk/257664-strada-1-7td-el-engine-torque-settings.html