Question about 1999 Chevrolet Silverado 1500

1 Answer

Starting problems not always will the sarter engage it always spins

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Chevrolet Expert
  • 495 Answers

Starter spining indocates bad solenoid...replace starter

Posted on Nov 20, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter spinning but not always engageing on my 2012 Hyundai sonata


The starter/solenoid is going bad, (flat spots) will need to replace, hopefully under warranty...please don't get stranded...last resort if stranded...tap starter with hammer, and try to start again...

Jun 21, 2014 | 1991 Isuzu Rodeo

1 Answer

Wat are some symtomes of a bad flywheel


Hi Adam, Typically a flywheel gives very little problem throughout its life span, but ca have worn on older vehicles. I'm guessing your problem occurs when engaging the starter motor? If it spins but does not always engage, it usually indicates a problem with the starter motor Bendix, but can also be related to a damaged ring gear which is mounted onto the circumference of the flywheel. Hope this answers your question? Regards John

Jul 21, 2013 | Cars & Trucks

1 Answer

Will bad a pilot bearing cause the sarter noisy


It is not the reason, but if the clutch does not fully disengage from the Flywheel, extra drag could occur.

If you can still drive the car, have a starter draw test performed with the transmission in neutral. The draw test can show the health of the starter. For that matter, use the Emergency brake and start the car in neutral anyway, although you may need to press the clutch to engage the starter. See if there is less noise by starting in neutral.

Apr 01, 2013 | 1990 Ford Mustang

1 Answer

Starter staying engaged after starting on 2005 malibu ls


check to engagement wire at the starter, make sure that power is only present when key is in the start position.if this is the case, then your sarter bendix is hanging up on the flywheel, this is caused by either inproper shiming where the starter is bolted to the block, or having the wrong bendix on the starter, there or several different bendix s general motors uses, also if the return spring in the solonoid is broken or not strong enough the starter could hang up. if the problem is power continuing to feed the solonoid with the key in the run position you could have a bad or out of adjustment ignition switch, since the power feeds the solonoid directly from the ignition switch, other than the neutral switch on the colomn

Jul 23, 2012 | 2005 Chevrolet Malibu

1 Answer

1982 Pontiac Firebird Trans Am, starter solenoid only engages sometimes (starter motor always spins), occasionally starter gets stuck ON, and sometimes no spark (fuel is fine but car won't start u


ANY FAULT CODES? HAVE YOU CHECKED THE STARTE DEPTH FOR PROPER CLEARANCE? HAVE YOU RITIATED THE FLYWHEEL TO LOOK FOR MISSING TEETH? I HAD AN 82 T/A AND THAT WAS WHAT CAUSED MY STARTER PROBLEMS. AS FAR AS NO SPARK DO YOU HAVE ANY FAULT CODES INTHE ELECTRONICS? TO TEST WITHOUT A SCNNER GO TO THIS LINK

Feb 11, 2012 | Cars & Trucks

1 Answer

WAS HAVEING PROBLEM WITH SARTER BECAUSE MY FLYWHEEL WAS MISSING TEETH JUST PUT IN NEW FLYWHEEL AND CLUTCH STILL HAVING PROBLEMS GETTING IT TO START DONT KNOW IF ITS SHIMED WRONG OR IF ITS THE WRONG STARTER...


It may be the starter dive teeth are worn from hitting the flywheel. Replace the starter drive or easier yet just install a rebuilt starter. If there were shims in the old one replace the shims in the proper location or you may need to either leave them out or add more to be sure the starter drive is properly engaging the flywheel.

Feb 24, 2011 | 1988 Ford F 250

2 Answers

Intermittent starting problems


I have similar problem with wife's B200. Am told it's the neutral/park sendor in the gearbox, which prevents car starting unless in park or neutral. Dealer wants AUD$1200 to remove gearbox to replace faulty switch sensor. Will update this website on repair outcomes.

Jun 18, 2009 | 2008 Mercedes-Benz Mercedes Benz E Class

1 Answer

Ford F150 starter does not engage, spins the catches off and on


Most Likely The Starter I Know We Changed It Is What your Thinking.
I Done 3 In A Row And The Fourth One Was Finally Good.

Jan 21, 2009 | 2004 Ford F150

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...