Question about 2000 Hyundai Elantra

Open Question

2006 Hyundia Elantra GT (Is the engine non Interference engine?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 566 Answers

SOURCE: how do you get rotor off 2003 hyundia elantra

hi from uk not sure if same as uk hyundai's but here goes ? if you remove wheel do you see two countersunk posi screws between studs that appear to hold rotor ?? if so then you will have to first remove the brake caliper assy by unbolting from the rear of caliper two 13 mm spanner/socket ? then you remove the two bolts that secure the carrier that the caliper bolts to 17 mm spanner/socket now you can remove the two contersunk screws then you may have to tap the rotor off the hub from rearuse a wire brush to clean up/away all rust/dust from caliper and carrier assys b4 refitting (take precautions from breathing dust) i assume you are fitting new pads ?? reassemble carrier then b4 fitting pads smear a light coating of copper grease on the rear of pad (metal side ) this prevents squealing on brakes then fully reassemble then b4 fitting wheel? bleed the brakee caliper a couple of pumps should expel dirty fluid then fit wheel carry out same proceedure on other brake assy as above fully then b4 you move car pump brake to ensure pedal is firm you will find that bleeding brakes will make pedal firmer as the old fluid becomes compressable due to heat/moisture absorbsion over time and heat from brakes is transferred to fluid via caliper piston understand?? that is why alway policy to bleed/flush brake fluid at least two yr interval this reduces spongy brake pedal hope this is all clear 4 you to follow best wishes for new year and hope you update on how you go on??

Posted on Jan 10, 2009

emissionwiz
  • 75822 Answers

SOURCE: interference engine

all of the engines used in the hyundai's are interference engine's, that does not mean for sure u have bent valves but the chances are u did. source of info Gates timing belt Catalog.

Posted on Mar 20, 2009

ghost4548
  • 776 Answers

SOURCE: engine code p0115

The Engine Coolant Temperature (ECT) sensor is located in the coolant passage of the cylinder head. The ECT sensor is a variable resistor whose resistance changes as the temperature of the engine coolant flowing past the sensor changes. When coolant temperature is low, sensor resistance is high; when coolant temperature is high, sensor resistance is low. The Engine Control Module (ECM) checks ECT sensor voltage and uses the information to adjust fuel injector pulse width and ignition timing. When the temperature sensed is very cold, the ECM enriches the fuel mixture and advances ignition timing. As coolant temperature rises, the ECM reduces the amount of enrichment and timing advance. ad5a8e2.jpg P0115 is set when the ECM doesn't see this resistance (usually an open circuit) which usually means the sensor is burned out when there's nothing wrong with wiring and connections between the sensor & the ECM.

Posted on Jun 02, 2009

SOURCE: i need to replace my timing belt on my hyundia

Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Posted on Sep 22, 2009

iambanshee74
  • 3489 Answers

SOURCE: What kind of anti-freeze goes into a 2001 Hyundia

i trust you are talking about the radiator(ive had people refering to their a/c system recharge as installing the anti freeze). this takes a standard good quality anti freeze/coolant mixed with distilled water.

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I would like to know If my 3.8l engine in my car has a non or interference engine in it


most newer vehicles are interference, basically if the timing chain or belt breaks it will cause internal engine damage. eg: bent valves, broken pulleys.

Apr 07, 2016 | 1999 Pontiac Grand Prix GT

2 Answers

I have an Isuzu kb 350 and has a broken timing belt and now is failing to start because of not sure of piston position in relation to dual camshafts


be VERY careful! Most engines are interference motors and a bust timing belt results in catastrophic failure when the valves contact the pistons because they are out of sync!

Timing belts usually come with markings - you would almost certainly find the compression TDC for cylinder 1 (not exhaust TDC - if the air blows thru plug hole when piston is rising its compression - if the air is NOT blowing out plug hole its exhaust tdc - rotate once more).

Now you will have to find the timing marks on the camshaft(s) and set according to the manual.

Mar 22, 2016 | Isuzu Cars & Trucks

1 Answer

Chrysler Sebring 2001 3.0 v 6 sohc interference motor or non interference I've seen answers that it was and then it wasn't


Chrysler
  • 1.4L, 1.5L & 1.6L Interference
  • 1.7L Non-Interference
  • 1.8L Interference
  • 2.0L DOHC Interference
  • 2.0L SOHC Interference
  • 2.2L DOHC Interference
  • 2.2L SOHC Non-Interference
  • 2.22L SOHC Interference
  • 2.3L Diesel Interference
  • 2.4L DOHC Non-Interference (Valves may hit if camshafts turn out of time)
  • 2.4L SOHC Interference
  • 2.5L 4 Cyl. Non-Interference
  • 2.5L V6 Interference
  • 3.0L SOHC 12 Valve Engine Non-Interference
  • 3.0L DOHC Interference
  • 3.0L SOHC 24 Valve Engine Interference
  • 3.2L Interference
  • 3.5L Interference
  • 4.0L Interference
  • this should be what your looking for.

Dec 10, 2015 | Chrysler Cars & Trucks

1 Answer

Is it fitted with an interference or non- interference engine?


Unable to find the exact answer.
In that vehicle its one of the Daewoo/Suzuki S-Tec Engines.
Due to it being high compression and its modern design, it most likely is an interference engine.

Sep 01, 2015 | 2006 Chevrolet Kalos 1.2

1 Answer

Non-interference engine chart


If you have either a 4 or 6cylinder, they are both interference engines.

Aug 12, 2014 | 2006 Saturn ION

1 Answer

Does 2006 pt cruiser have a clearance engine or non clearance engine


It is classified as a non-interference engine (not clearance)

Sep 20, 2012 | 2001 Chrysler PT Cruiser

1 Answer

Are the interference heads or non interference heads on a 2006 KIA Spectra EX


  • Kia Spectrs and Sortage are non interference. All other Kia engines are interference. So your vehicle is non-interference.

  • Hope this helps.

Oct 22, 2011 | 2006 Kia Spectra

1 Answer

Taillights for 2001 hyundia elantra


its real easy open trunk lid take rear sill off should just pop off then take trim panels each side then there are 4 bolts each side 10mm tkae bolts out firmly pull on tail lights they should come out and then reverse back

Jan 26, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...