Question about 2006 Mercury Montego

Open Question

How to reset ecu on 07 montego - 2006 Mercury Montego

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get my 07 Iveco daily to start as I changed all the fuses as I had blown the wiper one and now the immobiliser does not let me start it.


Try starting from scratch, disconnect battery for a few minutes and reconnect, ECU are usually reset and it may clear this default in your immobilizer. FREE-PPV.com

Apr 03, 2016 | Cars & Trucks

1 Answer

How do I know if the ECM computer is bad on my 2007 Acura MDX?


Installing J&R ECU - YouTube

? 2:29
www.youtube.com/watch?v=mRyDo0-JBQ0
Mar 19, 2012 - Uploaded by Aaron Wise
Installing J&R ECU on 2007 Acura TL-S. ... 2013 Acura TL SH-AWD Review, Walkaround, Exhaust, Test Drive - Duration: 14:16. by Redline ...

Immobilizer bad? ECU bad? - AcuraZine Community

acurazine.com/forums/problems.../immobilizer-bad-ecu-bad-863716/
Jul 21, 2012 - It says to have the ecu reprogrammed and if that doesn't work then to .....Join Date: Oct 2007 .... If relay tests good move on, if not replace it. total cost under $20 .... Check Emissions CEL, hrothgar02, Second Generation RDX ... Scanner not detecting ECU
May 22, 2012
Dealership "Re-Programmed" 07 TL Type S computer??
Jun 22, 2011
Resetting ECU makes me happy :)
Oct 9, 2009
Resetting your ECU: After mods and Environment changes
Jan 9, 2008
More results from acurazine.com

Oct 29, 2015 | Cars & Trucks

1 Answer

Mercury montego


chech lambda sensor or ether not anough air check air filter engine temp sender to ecu or possably blocked exhaust

Dec 30, 2013 | Cars & Trucks

1 Answer

How do I reset the oil light on my 2006 Montego?


This is on page 66 of the owners manual

To reset the oil monitoring system to 100% after each oil change

[approximately 5,000 miles (8,000 km) or 180 days] perform the

following:

1. Select this function from the

SETUP control for current display

mode.

2. Press and release the RESET

control to display "HOLD RESET

TO CONFIRM".

3. Press and hold the RESET

control to display OIL LIFE SET TO
100%. Your oil life is now reset.

Nov 18, 2010 | 2005 Mercury Montego

2 Answers

How do you reset the change oil message on a 2007


Ford Explorer, Mercury Mountaineer, 2002-07
To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the SET UP control to access the System Check mode. Press and release the RESET button to display “OIL LIFE % HOLD RESET NEW” is displayed. Press and hold the RESET button for 2 seconds until “IF NEW OIL HOLD RESET” is displayed. Press and hold RESET button until “OIL LIFE SET TO 100%” is displayed.
Ford Five Hundred, Freestyle, Mercury Montego 2005-06 Tap the ODO/TRIP button to toggle the display between the odometer and trip odometer. Tap on the ODOiTRIP button again to toggle the display between the trip odometer and OIL LIFE % display. Press and hold the ODO/IRIP button for 2 seconds or more to display OIL LIFE 100%. Your oil life in now reset.

Jan 06, 2010 | 2003 Mercury Mountaineer

2 Answers

How do i reset the check engine light?


disconnect the battery......wait three to five minutes. reconnect

Dec 29, 2009 | 2005 Mercury Montego

1 Answer

Oil change light


Look up the light on the part of your owners manual that explains what each idiot light is for on your dash. That should give you a page where more information on it is available. Part of that section should state that if maintenance is done by someone other then your Mercury dealer, then do the following to reset the light. That should take care of ya.

Good Luck

Dec 15, 2009 | 2005 Mercury Montego

1 Answer

How to collapse a rear caliper on a montego 07


Use a large "C" clamp and a old brake pad, to cover both pistons.

May 27, 2009 | 2006 Mercury Montego

1 Answer

2005 mercury montego message center


LOL!!! I had the same problem. I can't recall the exact steps, but there aren't that many options, so you'll get this. With the car running, press the Info button on the left side. It will cycle through the various statuses of the car. At one point, it will get to the Oil and will tell you something like "Press Reset if New." Press it and hold that darned button until it acknowledges that you changed the oil. It will reset that message from 0% to 100%. It took me a couple of tries to get that to reset. Just keep trying it till it resets. You'll get it.

Jan 21, 2009 | 2005 Mercury Montego

Not finding what you are looking for?
2006 Mercury Montego Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...