Question about 2005 Ford Escape

Open Question

Replace center support bearing on rear drive shaft 01 ford escape

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fknstart
  • 404 Answers

SOURCE: removal of rear brake drum 2002 ford escape

make sure handbrake is off take wheel off hit the drum with a mallet not steel,as it will brake,hit on outter diametter face of drum, try and rotate as you twist off

Posted on Jan 05, 2009

  • 508 Answers

SOURCE: Right-Front Intermediate Axle Shaft Bearing

I am assuming this is an all wheel drive. That being the case you probably have an axle CV joint going out. If you hear noise when making a sharp left or right turn and accelerating that would more than likely be the problem. And, yes this is a serviceable part. Easy to replace if you have the proper tools to accomplish the task. Good luck.

Posted on Feb 18, 2009

michigan man
  • 3533 Answers

SOURCE: How to replace front wheel bearings on a 2001 Ford Escape 4X4

try "autozone.com" or your local library for diagrams and step by step instructions

Posted on Mar 08, 2009

jaysonemanme
  • 500 Answers

SOURCE: Rear Wheel bearing needs to be replaced

the bearing has to be pressed in, quite the job even doing it at the shop- you will have to have some sort of press to press the bearing in.

Posted on May 20, 2009

  • 27 Answers

SOURCE: replace rear wheel bearing 2002 ford explorer 4x4

you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AFTER REPLACING U-JOINTS & HANGER BEARING ON MY 1995 VOLVO 960 I HAVE VIBRATION AT SPEED PARTICULARLY UNDER ACCELERATION. I TRIED ANOTHER SHAFT AND IS WORSE. I THINK IT MIGHT BE HANGER BEARING ALI


did you mark the two ends of the shaft at gearbox and diff
so they lined up again
with the center bearing replacement
did you mark the two halves before separating and replacing the center bearing
then make sure they lined up again

if vibration is there
you may need to go to a diff shop and have the drive shaft balanced properly

very informed drive shaft write up.. on volvos
Driveshaft Rear AxleDriveline Rear Axle
26328039-dr1l0prezoqh0gobrdoiolxi-5-0.jpg

Oct 26, 2016 | Volvo Cars & Trucks

1 Answer

When i slow down theres a popping coming from rear


could be worn suspension, also check rear brakes for wear, rear differential and drive shaft, u-joints.Can also be rear axle bearings.

Feb 17, 2013 | 2003 Ford Escape

1 Answer

I'm trying to figure out how to remove a bearing from driveshaft off 2002 lincoln ls


Which bearing? The hub bearing? I can send it. I have your Ford shop manual & wiring books for $25, plus $4 shipping. Let me know.

SECTION 205-01: Driveshaft 2002 Lincoln LS Workshop Manual
DISASSEMBLY AND ASSEMBLY Driveshaft Center Bearing
Special Tool(s) s2x~us~en~file=st1260a.gif~gen~ref.gif 2-Jaw Puller
205-D026 (D80L-1002-L) or Equivalent s2x~us~en~file=st1368a.gif~gen~ref.gif Puller, Bearing
205-D064 (D84L-1123-A) or Equivalent s2x~us~en~file=st2454a.gif~gen~ref.gif Driveshaft Alignment Bushing Remover Tube
205-D073 or Equivalent
Disassembly
  1. Remove the driveshaft (4602). For additional information, refer to Driveshaft in this section.
  1. Separate the front and rear shaft assemblies.
  1. s2x~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not clamp on the driveshaft tube as a fracture can result.
    Position and clamp the driveshaft at the weld yoke.
  1. Using the special tools, remove the retaining ring and the center bearing and bracket assembly (4A499).
Assembly
  1. Position the center bearing and bracket assembly and the retaining ring on the yoke.
  1. Using the special tool, drive the retaining ring and bearing assembly until fully seated on the yoke.
  1. s2x~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Align the index marks or driveshaft imbalance can occur.
    Assemble the front and rear shaft assemblies.
  1. Install the driveshaft. For additional information, refer to Driveshaft in this section.

Sep 08, 2011 | Lincoln LS Cars & Trucks

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

2 Answers

2005 ford escape 3.0L AWD XLT - DRIVESHAFT CARRIER BEARING BAD - CAN IT BE REPLACED OR MUST I CHANGE THE DRIVESHAFT FRONT AND REAR?


if there is some one in your area that balances driveshafts they can change just the bearing for you

Nov 10, 2009 | 2004 Ford Escape

3 Answers

2005 ford escape awd shutters very badly upon take off up to about 30 miles per hour then gets progressively better. Is the center drive shaft bearing bad and is it repairable . Ford says the driveshaft...


Have a 2005 ford escape XLT 4WD and when I get between 45-60km per hour the vehicle shakes like I'm driving on a washboard. Took it to Ford - they told me I need a new drive shaft - $1200 with taxes and labour. I already replaced the alternator in 2007 - that was over $800 because of where it is positioned. Takes hours and hours to get at it because it is buried under the motor. I think Ford needs to give us all a discount. Sounds like these are common problems with the Ford Escape.

Oct 07, 2009 | 2001 Ford Escape

1 Answer

How to remove and replace rear wheel bearing on a 2005 ford escap


remove tires remove the center cap to reveal a 22"nut remove nut pull out brake disk assembly on the brake disk assembly, replace wheel bearing

Jul 16, 2009 | 2005 Ford Escape

2 Answers

Rear wheel bearing


SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Apr 10, 2009 | 2004 Ford GT

1 Answer

2001 Ford Escape AWD Drive Shaft center support bearing?


its called a steady bearing, take the drive line behind it off then youll see a larger nut you un screw and it will all come apart from there

Mar 13, 2009 | 2001 Ford Escape

Not finding what you are looking for?
2005 Ford Escape Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...