Question about Acura CL

1 Answer

How do yoou remove the old and then replace the new alternator on a Holden 2000 statesman

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 20,706 Answers

And acura CL holden swap?

Posted on Nov 28, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 370 Answers

SOURCE: i have a holden statesman

ok fuse and bulbs are ok then you have to start looking at switches there is a switch on the arm of the brake pedal, use a test light and make sure 12 volts is going through the switch then that voltage goes upto the multifunction switch in the stearing colum, this has your hazard lights, turn signals, and bright headlamp controls in it, check this by turning on the hazard lights see it the tail lights flash this uses the same wire as the brake light so if it lights you have a bad brake switch at the pedal, if nothing lights up 90% chance its the multi function switch

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i stop a fuse blowing in the interier system in a holden statesman wh v6


the wires will be shorting out maybe to the body of the car. it may be easier to run new wires from the fuse to the visor and then cut old wires than try to trace the old wires under the head lining .

Jun 29, 2016 | Holden Cars & Trucks

1 Answer

How to Replace an alternator on a 2003 statesman


Im assuming the alternator your replacing is on a v6 statesman.
1.disconnect battery
2.remove engine cover
3.remove drive belt
.remove 10mm bolt that holds bracket from eng to alternator
4.remove all wiring from the rear of alternator.
5.remove the 2 bolts that holds the alternator to engine.
6.wiggle alternator and it will slip out.;
7.refit new alternator in these steps but reversed.
8.once up and running again please make sure you check the system charge rate..

Feb 16, 2015 | Holden Cars & Trucks

1 Answer

How to fix LHS front door remote. Lock on holden statesman wl


more than like if its just on door that wont look and the hoon sounds the door actuator will be faulty and you will need to replace the actuator.
To do this you will need pull the inside door handle off.
remove all door trim covers to access screw and disconnect mirror wiring.
remove all screws around door trim.
very carefully remove door trim once the trim is off you see a plastic inner door liner don't rip gently remove half .
look inside door and you will see the door actuator and lock,carefull lift up locking tabs so you can remove all door rods from actuator.
on the outside of door undo the 3 bolts and actuator will come out.
get the new actuator and fit it the same way the old one come out.
Before refitting the trim grab some silicon and reseal plastic to door to keep water out..

Dec 06, 2014 | Holden Cars & Trucks

1 Answer

Where is the ecu located on a vq statesman


it may be on the passanger side floorwell infront of the frontdoor pillar near where your left foot would rest. should be a plastic plug to remove then the carpet or moulding covering the ecu

Sep 30, 2014 | 1992 Holden VQ Statesman

1 Answer

Replacing sway bar


remove the nut from the link bolt and slide out. the bushes have metal washer plates between them ,keep them in order as you remove them helps when refitting.

Jul 08, 2014 | Holden Caprice Cars & Trucks

1 Answer

How to replace bonnet struts WK holden statesman


To Replace bonnet struts on a wk statesman you will need to flow the procedure below.
1.Open the bonnet fully
2.Replace one at a time .
3.Now bonnet is open grab pole and place under bonnet for extra support.
4.The strut will be mount to a ball and on the side you will also see a little rectangular clip .
5.Use a small flat blade screw drive to pop clip out once the clips out you will be able to gently work the strut off the ball on top and bottom.
6.same procedure to fit new strut

hope this helps

Jul 07, 2014 | 2006 Holden Commodore SS

1 Answer

Overflow tank


try the Holden wreckers for a replacement . many statesman parts are interchangeable with the same year Holden sedan series.. There are after market reservoirs that will fit as well.

Mar 29, 2014 | 2002 Holden Caprice

1 Answer

VS statesman no horn / airbag light on


that work should be done in a garage ,as danger of setting off the airbag .

Dec 23, 2013 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...