Question about Cars & Trucks

Open Question

2002 nissan frontier knock sensor wiring harness location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: location of knock sensor

Knock sensors can be difficult to locate because there usually buried under intake or exhaust manifolds and misc. engine wiring and plumbing. Knock sensors need to hear an engine knocking noise, therefore there usually located somewhere they can hear an engine knock. If it's a V6 then possibly it will be between the cylinder heads and access to them can only be attained by removing the intake manifold. I would suggest calling a Nissan Dealer parts person and ask them. Good luck.

Posted on Jun 16, 2009

emissionwiz
  • 75189 Answers

SOURCE: Where is the knock sensor located on a 2003 nissan

It is located on the engine block itself in the valley between the cylinder heads. The entire intake manifold has to come off to access it:

Posted on Oct 30, 2009

Testimonial: "I am well satisfied with the quick response and information. Chuck"

ZJLimited
  • 17970 Answers

SOURCE: Diagram available for 01 Nissan Xterra Knock Sensor location?

V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Posted on Feb 08, 2010

samtoler
  • 666 Answers

SOURCE: I need to replace the knock sensor in my 2000

it is located on the bottom section of engine, Just unplug it and it screws out fairly easy

Posted on Jun 14, 2010

twoduckster
  • 370 Answers

SOURCE: 2001 nissan frontier 3.3 super

Its located behind the air intake, by the firewall. It looks like a doughnut with rubber on it, and a wire coming out of the side. Its held down by a bolt. Its just in a hard place to get to. If you remove the bolt first, its easier to pull up by the wire. disconnect the wire, and throw away, connect the new one, and bolt the new one in. ONLY use 20lbs. torque to tighten it down. It will break if not careful(found out the hard way). Its about a 10 minute job

Posted on Jan 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which wire is positive left or right on the knock sensor harness for 2004 Nissan Frontier


I believe its the right, but if I am not mistaking, it does not actually matter.

Aug 01, 2016 | 2004 Nissan Frontier XE

1 Answer

Where I can locate po325 knock sensor for nissan frontier 2000


underneath intake manifold between cylinder 1 and 2.

Mar 09, 2015 | 2000 Nissan Frontier

1 Answer

Where is the knock sensor located


They are located under the intake manifold, one for each bank of cylinders in the 4.0L. Replace the sensors as well as the stub wiring harnesses to them. See picture below of a sensor.
9_12_2012_9_39_31_pm.jpg

Sep 12, 2012 | 2002 Nissan Xterra

1 Answer

2001 nissan frontier 3.3 super charge knock sensor location


Its located behind the air intake, by the firewall. It looks like a doughnut with rubber on it, and a wire coming out of the side. Its held down by a bolt. Its just in a hard place to get to. If you remove the bolt first, its easier to pull up by the wire. disconnect the wire, and throw away, connect the new one, and bolt the new one in. ONLY use 20lbs. torque to tighten it down. It will break if not careful(found out the hard way). Its about a 10 minute job

Jan 17, 2011 | 2002 Nissan Frontier Crew Cab

2 Answers

Replacing knock sensor do I need to replace the harrness


No you don't have to change the harness unless it is cracked, broken, or have burn marks.

Nov 10, 2010 | 2000 Nissan Frontier

1 Answer

Where is the knock sensor located?


the knock sensors (there are 2) are located under the intake manifold, u must remove the intake maniofold to replace them, also u will need the new stub wiring harness most likely to each sensor and a set of intake gaskets

Feb 04, 2010 | 2002 Nissan Quest

1 Answer

2002 Nissan Frontier Super charged has bad "knock sensor" Where is this part located ?


the knock sensor on a 3.5L should be just under the exhaust ports on the right side of the engine if you're facing the side with the pulleys and crank(front) for the life of me, I cant remember if the engine is mounted longitudinally or tranversely in the frontiers.....lol. There should be a wire going to a small black thing thats just kind of there,... its really easy to miss. if you can, check the nissan forums or somewhere online the e-manual that should have the exact placement of it in diagrams.

Oct 14, 2009 | 2002 Nissan Frontier Crew Cab

1 Answer

Location of knock sensor


Knock sensors can be difficult to locate because there usually buried under intake or exhaust manifolds and misc. engine wiring and plumbing. Knock sensors need to hear an engine knocking noise, therefore there usually located somewhere they can hear an engine knock. If it's a V6 then possibly it will be between the cylinder heads and access to them can only be attained by removing the intake manifold. I would suggest calling a Nissan Dealer parts person and ask them. Good luck.

Jun 16, 2009 | 2004 Nissan Frontier

1 Answer

Iat sensor location for a 2002 nissan frontier?


Depending on what size engine you have, it could be on the air filter housing,or somewhere along the intake tube that goes to the throttle body. It's round in shape and has 1 or 2 wires connected to it.Without the size of the engine, I can't tell you exactly where it is.

Mar 12, 2009 | 2002 Nissan Frontier Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...