Question about 2010 Volkswagen Passat CC

Open Question

Steering wheel buttons not working - 2010 Volkswagen Passat CC

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My horn isn't working on a Chevy equinox but it's a new horn. What could be wrong with it..and my cruise control don't qork. Is it my steering wheel?


Was Cruise Control working before the New Horn was installed? The power supply to the Horn, (input to ground wire) is connected to the Cruise Control Module (CCM). This CCM is wired to the Relay Switch Box located in the Engine Bay. The Relay Box cover will have a Chart indicating what function each Relay coresponds to. Your local autoparts store (AutoZone) can test the Relay Switch, and you'll know (if any Relay) need to be replaced.

The CCM is also wired to the Steering Wheel, but first passes through the Clock Spring Coil, located just behind the Steering Wheel. The Clock Spring allowes for the Function Buttons on the Steering Wheel to have power while Steering Wheel spins.

The Clock Spring can malfunction or break, its rare, but this will cut power to the Function Buttons on Steering Wheel. If ALL the buttons on Steering Wheel dont work, then the Clock Spring is the Culprit. The Coil may need to be replaced.

The Cruise Control Module itself may have failed and also would cause a few or all Steering Wheel Functions to quit working.

But first check the Relay Switch Box and examine the Harness Cables connecting (Steering Wheel--to--CCM--to--Relay Switch Box--to--Battery Supply).

Also if Cruise Control was working before the new Horn was installed and now not working, then most likely the Problem is a bad wire connection somewhere and/or is a faulty Relay.

(Any Questions/comments jtobias1020@gmail.com)

Feb 26, 2017 | Chevrolet Equinox Cars & Trucks

1 Answer

Toyota 2007 Prius Touring


Usually when it works, then doesn't. Then you shut off power and turn it on and it works again. It is a module. Yours would be the steering module. These are the hardest problems to diagnose(any of the computers on the car can do this). You just spent too much for someone telling you every thing is OK. But not really. Now comes the electrical part. Checking everything from the switch to the computer and making sure it is good.

Aug 20, 2016 | Toyota Cars & Trucks

1 Answer

MY LOW BEAM LIGHTS, BREAK LIGHTS AND RADIO SOUND CONTROL ON STEERING WHEEL, ALL STOPPED WOKING


Steering wheel radio controls and horn not working - Jeep Wrangler ...

www.wranglerforum.com/.../steering-wheel-radio-controls-and-horn-not...

Sep 22, 2014 - 12 posts - ‎6 authors
... 2Dr sport and my step/reset buttons, radio control and horn all stopped working. ... Also the lights behind the step/reset and cruise control went out, but the ... Soundslike a bad clock spring ribbon cable in the steering wheel. steering wheel buttons not working
30 posts
Jun 14, 2012
Steering wheel audio controls
30 posts
Mar 5, 2011
More results from www.wranglerforum.com

Nov 23, 2015 | Cars & Trucks

1 Answer

How to fix + and mute buttons on steering wheel


you can buy the switch from the dealer and they change very easy

Jun 10, 2015 | Cars & Trucks

1 Answer

I replaced factory deck and now steering wheel volume and seek button do not work. Is there something I can do


The buttons in your steering wheel are designed to work with the factory radios only. If you replaced the radio with anything other than a factory radio your chances of getting the steering wheel buttons are pretty slim.

Mar 31, 2015 | Cars & Trucks

1 Answer

Horn on 2007 pontiac G6 stopped working, what can I do?


check fuses check to see if the other buttons on the steering wheel work if there are any (not the ones on the steering column if there are any buttons on the steering wheel try them) if all fuses are good and nothing on the steering wheel works there is a plastic disc between the steering wheel and the steering column this makes the electronic connection the part may run between 50-200 dollars depending on the car its a pain if you dont know how to replace it so you need a mechanic thats going to dig in your pocket sometimes its better to just go without a horn and just use your finger good luck

Dec 21, 2012 | 2007 Pontiac G6

1 Answer

I just replaced my turn signal switch in my 82 not 84 rampage. it works fine but when I replace the steering wheel, the horn honks and won't stop.when I look at the switch, I don't know how it...


I don't have a diagram, but if I understand what you're saying, there is a copper ring at the top of the steering column, visible before you install the steering wheel. The copper pin is connected to the horn button. The intent being that when you press the horn button, it completes the ground from the steering wheel through the horn button, through the pin, to the copper ring.
If this is correct, there should be no contact between the steering wheel and the copper ring other than the pin. Check to see if there may have been a spacer (washer, etc) below the steering wheel on the steering shaft that holds it just far enough away from the copper ring so that only the copper pin makes contact.

May 01, 2017 | Dodge Rampage Cars & Trucks

1 Answer

How do you take the air bag out the steering wheel in order to check the horn switch? Horn works with the remote button but will not work when horn button is pushed on steering wheel!


You should never try to take apart the airbag unless you absolutely know what you are doing for you can injure yourself very seriously.But on that note,disconnect the battery.Behind where you grab on the steering wheel there should be some screws.Take those out and remove the front of the center of the steering wheel.That will give you access to the airbag.You may have to have special tools to take the airbag itself out.Then there should be the switch.If it is not there you might have to remove the whole steering wheel by removing the center nut then use a steering wheel puller to take the steering wheel off.It should be located on the steering wheel shaft.

Oct 01, 2010 | 2003 Pontiac Grand Am

1 Answer

2000 SERRIA, HORN WILL NOT WORK WHEN YOU DEPRESS THE HORN BUTTON, WILL SOUND OFF WHEN YOU PUSH THE ALARM BOTTON, WHAT IS THE SOLUTION. JOE, POQUOSON VA.


If the horn works with the alarm button but not with the steering wheel horn pad the problem is most likely in the contacts beneath the steering wheel. This requires pulling the steering wheel and repairing the contacts.
If this vehicle has an air bag in the steering wheel make sure to deactivate the airbag circuit before pulling the steering wheel.

Nov 05, 2009 | 2000 GMC New Sierra 1500

1 Answer

Buttons on steering wheel do not work


have your mechanic check you STEERING WHEEL control module its the unit the control the function on the steering that communicate with veh ecm

Aug 07, 2009 | 2000 Ford Windstar

Not finding what you are looking for?
2010 Volkswagen Passat CC Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...