Question about 2004 Lincoln Navigator

Open Question

1998 jeep 2.5 po320 code - 2004 Lincoln Navigator

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could po320 be drive shaft speed sensor


code p 0320 refers to crankshaft position (CKP) sensor /engine speed (RPM) sensor---circuit malfunction====causes --wiring--CKP/RPM sensor ---ECM check the wiring to the crank position sensor
replace the crankshaft position sensor

Apr 16, 2017 | 2004 Jeep Grand Cherokee

1 Answer

What does code PO320


According to my code manual PO 320 code means ,There is no signal to the crank shaft position (Sensor)

Nov 10, 2012 | 1998 Jeep Cherokee

1 Answer

96 jeep cherokee 4.0 has no spark po320 shows could the cam sensor cause it to have no spark


Cam sensor, crank sensor, bad coil, all could give no spark. Check all fuses and relays.... wiring connections as well. 320 is a crank sensor code.

Aug 25, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Our Jeep liberty Po320 code than misfire replaced parts and same codes again than stalls after it get warm. Could this be a PCM units


disconnecting the battery will only temporarily erase your code or check engine light. put your keys in the ignition, then turn it in the on position. Do not turn it so that the engine turns over, but as if you were just turning the radio on. Keep it on for 2 to 4 seconds repeat 40 times. i no it may take a while but unless you have a scanner its the only way.

Jan 16, 2010 | 2002 Jeep Liberty

1 Answer

1998 chevy lumina cranks fine good spark no fuel puup power code po320 fuel pump problem circuit need help


Check the APV fuel pump relay under the hood. And check you fuse inside the car.

Dec 30, 2009 | 1998 Chevrolet Lumina

2 Answers

2003 Jeep Liberty Stalls


thats correct, may have bad ecm (computer) or bad wire to crank sensor from ecm, also ive run into this problem and it was the new sensor i put in was no good and aftermarket,also cam sensor can do this, and also make sure the 5 volt feed wire is good,good luck hope this helps.

Oct 13, 2009 | 2002 Jeep Liberty

1 Answer

How do i locate a crank sensor and the code comes up as po320. thank you


Yes the po320 code is no signal at the crank.It is located on the transmission bellhousing.Its on the lefthand side of the housing in the top quarter.At the back of the motor.After the problem has been fixed,do not disconnect the battery to clear the code.Get the codes cleared before starting the motor or the comp may set a trouble code for that.A scan tool is needed from a dealer or good shop.I hope this helps

Sep 25, 2009 | 1998 Jeep Cherokee

1 Answer

FORD RANGER ENGINE PROBLEM


P0320 - Ignition Engine Speed Input Circuit Malfunction - The ignition engine speed sensor input signal to PCM is continuously monitored . P0320 indicates that two successive erratic profile ignition pickup ( PIP ) pulses have occurred Some possible causes are : loose wires / connectors , arching secondary ignition components ( coil , wires , + plugs ) , on board transmitter ( 2 - way radio )

Jul 14, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
2004 Lincoln Navigator Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...