Question about Cars & Trucks

Open Question

Mk1 golf 1.6i torque settings for cylinder head ,mains and big ends

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi its the torque settings for the cylinder head I am looking for on v w 14i 8 valve mk1 2007 golf


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Dec 29, 2016 | 2007 Volkswagen Golf

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

2 Answers

Hyundai elantra 1.6GLS J2 torque settings


dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

Aug 31, 2009 | 1995 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...