Question about Cars & Trucks

Open Question

How to set engine timing on toyota corolla 2006 model 160i gle

Marks for timing

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

AUTODOC01
  • 216 Answers

SOURCE: need to know the timing marks on 1992 toyota

you may find them online but if it were me i would go to local auto parts and spend the $24.95 on a haynes repair manual it has pictures of the marks and the tension specs etc worth the $$ , remove #12 spark plug and take a peice of wire stick it into the hole till it touchs the piston then rotate the crankshaft till its a top dead center then look down at the line up marks behind the crank gear they should line up then rotate the camshaft till marks line up should be 12 oclock on cam gear? this is sometimes tricky to get it lined up without it being 1 tooth off thats why picture is best ? hope this helps autodoc01@live.com

Posted on Aug 27, 2009

Danniboi
  • 1098 Answers

SOURCE: I have a 2004 Toyota Corolla 160i Gle, which has

Hmm sounds serious then, it's difficult to say without seeing the car but I would suspect they will have to check the cylinder head first to make sure its not coming from there. more likely from what you have said the bottom half of the negine would need to be stripped down and rebuilt before it causes more damage, like complete engine failure.

Posted on Jan 14, 2010

Testimonial: "Thank you for your prompt response and good advice. Much appreciated"

  • 906 Answers

SOURCE: toyota corolla 160i lost ignition

good day Sir, try to check the batter and spark plugs i hope this tips will help you.

Posted on Aug 04, 2010

SOURCE: Toyota corolla 160i GLE 1999 - NOT STARTING WHEN VERY COLD

You have to diagnose the car using a diagnostic tool to see if all the sensors are working. The cold start circuit will not activate unless the temp is below certain values.

Posted on Dec 14, 2011

  • 536 Answers

SOURCE: need timing belt marks diagram for mazda 323 160i , 2001 model, zm engine

11_30_2012_7_10_14_am.jpg
I would have liked to add as an attachment but could not.

Posted on Nov 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota corolla 160i gle model 2003 have airbags because light don't show up


2003 up corolla models may have one air bag
if so the air bag is part of the horn pad

air bag light and chime would be there only
if air bag system is faulty


26274311-wjya3n2etfq4tuodlgyyifbb-2-0.jpg

Sep 04, 2016 | Toyota Corolla Cars & Trucks

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

3 Answers

Setting timing marks to get vehicle to start after engine overhaul


Timing marks setting Corolla 4A-FE.
Align the notch on the crankshaft pulley with the "0" mark on the timing belt lower cover.
25679262-y0srr1ownybx5goll4rgvnpm-5-0.jpg

With the crankshaft pulley being aligned with the 0 mark on the timing belt cover, the hole on the camshaft sprocket should exactly be in front of the notch of camshaft bracket.


25679262-y0srr1ownybx5goll4rgvnpm-5-2.jpg
Hope that works.

May 04, 2015 | 1998 Toyota Corolla

1 Answer

Will toyota corolla 1800 with 1zz motor run with 1600 3zz ecu.


The settings would be completely different - you will need the 1.8 ECU

Dec 23, 2014 | 2006 Toyota Corolla

1 Answer

How to aline timing marks on hyundai elantra 2009 4 cyl.


valve timing, crank pulley T D C mark to mark on timing cover. Cam gear mark to mark on head or block . Ignition timing T D C mark on crank pulley to timing mark on timing cover.

Sep 21, 2014 | Cars & Trucks

1 Answer

Car jerks when driving


run fault codes and fix faulty sensors.

Jan 17, 2014 | Toyota Corolla Cars & Trucks

1 Answer

Noise air intake


moving only or all the time..........???????????????????????
this is a hands on deal, no web bunny can guess.
it takes tools and all senses to find this. humans, touching....
ok, ill guess. the tappet is bad.


most FSM have a huge chapter just on noise,that works about 10% of

http://www.fixkick.com/NOISE.html

3000 parts on the car, any can make noise. for sure moving.
start with a stethoscope.

Jan 11, 2014 | Toyota Corolla Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...