Question about 1995 Dodge Dakota

1 Answer

I have a 1993 Dodge Dakota 4wheel drive and cant find the filler plug on the transmillion. I have found 2 plugs on back of the transfer case. Will this be the filler plugs? What kind of oil do I refi

I have not found the filler plug on top or side.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 47,682 Answers

Gear box / transfer case filler plugs are about 1/2 way up the side of the unit. The lower plug (probably 1" lower is the oil level hole.. So remove the upper plug and fill till the oil runs out of the lower hole. Replace both plugs. The oil used should be a 80-90 oep oil

Posted on Nov 19, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: location of spark plugs in 2005 dodge dakota

To change the sparks on a 2005 4.7L Dodge Dakota you will need the following:

  • Spark plug socket
  • Ratchet
  • Torque wrench
  • Extension
  • Flat-tip screwdriver
  • Make sure the truck is cold!!!

Note you will have to remove the air intake located at the top of the engine, and will have to move some of the coolant lines out of the way.

At the top of the engine there are 4 sparks on each side. The coils are held in place with a 10mm bolt. Undo the 10mm bolt and unclip the coil. Next pull out the coil.

Insert the socket, with extension into the spark plug hole.

Remove spark plug.

Check the gap on new spark plug, it should match stock.

tighten to approximately 25ft.lbs. (check spark-plug packaging for exact torque requirements).

repeat this process with all other sparks.

be sure that no dirt gets into the spark plug holes.



Posted on May 11, 2009

  • 333 Answers

SOURCE: where is the transfer case control module located

It is located under the driver side dash, on the steering column. See diagram below:
0d1bdaa.gif

Posted on Oct 18, 2009

  • 5370 Answers

SOURCE: where is the transfer case

The transmission control module and the transfer case control module are separate parts. The transmission control module is mounted under the hood and controls only transmission functions. The transfer case control module controls only the transfer case, and is located inside the truck. If you remove the trim panel under the steering column you will find the transfer case control module mounted just to the right of the opening.


The shift motor is located just behind the axle tube to prevent damage.
There is a shift motor on the right front axle that is vacuum operated.
The shift motor (1) is an electromechanical device consisting of a DC permanent magnet motor, a motor brake, a gear train and an analog position sensor. The shift motors' overall function is to move and lock a gear that moves the mode fork found in the transfer case. This allows the transfer case to be shifted electrically to multiple operating positions (4LOCK and AWD). The operating current of the shift motor under
stall conditions is 30 amps maximum at 72° F with 13.5 volts, at the motor leads.
OPERATION
Shifting in the transfer case occurs when the shift motor brake is released and a Pulse Width Modulated (PWM) voltage is supplied to the shift motor by the Front Control Module (FCM). A linear analog position sensor located inside the shift motor, provides the FCM with the motors' angular, rotational position. With this information, the FCM
continuously knows the motors' position, and therefore allows it to accurately control the motors' operation, including voltage polarity which is used to control motor direction.

REMOVAL :---Note: New shift motor assemblies are shipped in the AWD position. If a new shift motor assembly must be installed, it will be necessary to shift the transfer case to the AWD position prior to motor installation.
Raise the vehicle on a suitable hoist.Remove the front propeller shaft. Disengage the wiring connectors from the shift motor and mode sensor.Remove the front output shaft companion flange from the transfer case.Remove the bolts (Remove the Shift Motor and Mode Sensor Assembly Bolts) holding the shift motor and mode sensor assembly onto the transfer case.Separate the shift motor and mode sensor assembly from the transfer case. See fig below:-- helpmech_19.gif
1 - TRANSFER CASE.2 - SHIFT MOTOR AND MODE SENSOR ASSEMBLY.3 - BOLT.-- This should help.Thanks.Helpmech.

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 dodge dakota cant get yhe traanfer case out of 4hi andno light on the switch


It might sound funny but sometimes you have to back up to get them out of four wheel drive mode...worth a try...Hope this helps....GOD BLESS....Randy

Nov 07, 2017 | Dodge Dakota Cars & Trucks

1 Answer

I have a 2002 dodge dakota the 4wheel drive will not work can you help me?


Your transfer case is electronically controlled by the transfer case control module (TCCM). It will only engage and change selections based on specific operating parameters. If you are not able to select any 4WD range, you'll probably have to use a compatible scanner to determine why the TCCM is not allowing selection (or to determine if it is working properly).

Oct 28, 2016 | Dodge Dakota Cars & Trucks

1 Answer

1995 Dodge Dakota V8 4x4 transfer stuck in neutral


hi i have a problem with my 2003 dodge Dakota i have it in 2h but it switches into fwd on its own can anyone help me with this problem

Sep 16, 2012 | 1995 Dodge Dakota

1 Answer

Front wheels not turning in 4wheel drive 1996 dodge dakota


Check and make sure the transfer case is adjusted right If the front end was broke you would know it. Jack up one front wheel and put it in 4wheel drive but not lock and see if the front drive shaft turns if it doesn't you need to adjust linkage or if it's electric make sure the signal is getting to the transfer case. If it only locks front and rear jack up one rear wheel also and do the check. Most people with 4 wheel drive don't know they have two wheel drive One in the rear and one in the front unless you ordered a locking dif from the factory they don't come this way. Then you would have 3 wheel drive

Dec 02, 2011 | 1996 Dodge Dakota

1 Answer

How much fluid does the transfer case hold for 1993 ford diesel


No idea but it must have a filler/level plug so you fill it to the level of the filler plug ,should imagine it will hold about 4 litres though but i could be wrong

Nov 20, 2011 | 1993 Ford F250

1 Answer

Hi i have a 1993 dodge dakota 2 wheel drive ext


when the 4-way flash you won't get the signal work!

Feb 27, 2010 | 1993 Dodge Dakota

1 Answer

What is the capacity of the transfer case and exactly what fluid do i use


GM Full-Size Trucks 1980-1987 Repair Guide

Transfer Case - FLUID RECOMMENDATIONS
The type of lubricant used in the transfer case varies with model year and type of transfer case. Refer to the list below for the type that applies to your truck.

1980
Conventional transfer cases require SAE 80W or SAE 80W-90 GL-5 gear lubricant.
Full time systems use SAE 10W-30 or 10W-40 engine oil.
1981
Conventional transfer cases require DEXRON®II transmission fluid.
1982-85
All transfer cases require DEXRON®II transmission fluid.
1986-87
All transfer cases except the K30/35 series require DEXRON®II transmission fluid.

For fluid recommendations for the K30/35 transfer cases refer to the owner's manual.
LEVEL CHECKS

fb6e8b4.jpg
Fig. Model 208 Transfer Case

Check the four wheel drive transfer case lubricant level every 4 months or 6,000 miles.
  1. With the truck parked on a level surface and the parking brake firmly applied, remove the filler plug from the rear of the transfer case (behind the transmission). Be careful not to take out the drain plug at the bottom.
  2. If lubricant trickles out, there is enough. If not, carefully insert a finger and check that the level is up to the edge of the hole, EXCEPT in full time four wheel drive cases should be 1 /2 in. below the hole.
Lubricant may be added, if necessary, with a funnel and tube, or a squeeze bulb.



DRAIN AND REFILL
Part Time Systems
No intervals are specified for changing transfer case lubricant, but it is a good idea for trucks that are worked hard or driven in deep water.
  1. With the transfer case warmed up, park on a level surface and apply the parking brake.
  2. Slide a pan of a least 6 pts. capacity under the case drain plug.
  3. Remove the filler plug from the rear of the transfer case (behind the transmission). Remove the drain plug from the bottom.
  4. Wipe the area clean and replace the drain plug.
  5. Add lubricant with a suction gun or squeeze bulb. Conventional transfer cases require SAE 80W-90 GL-5 Gear Lubricant.
  6. When the lubricant level is up to the bottom of the filler hole, replace the plug.
Full Time Four Wheel Drive
The full time system requires oil changes at regular intervals, according to the amount and type of work done by the unit. Trucks used for normal on-off road work should have the transfer case oil changed at 24,000 mile intervals. When used for heavy duty work, trailer towing, snowplowing, and the like, the interval should be halved to 12,000 miles. If the truck is exposed to extremely dusty or muddy conditions, the oil should be changed at 1,000 mile intervals.
The transfer case oil must be hot before changing. Drive the truck until the engine has reached normal operating temperature, and park on a level surface.
  1. Slide a pan of at least 8 pts. capacity under the case drain plug.
  2. Remove the filler plug.
  3. Remove the lowest bolt from the front output shaft rear bearing retainer cover, and allow the lubricant to drain. Be careful; the oil will be hot. There may be a drain plug. If so, remove that instead.
  4. Remove the six bolts on the left (driver's) side of the case which secure to P.T.O. (power take-off) cover. Remove this cover and allow the lubricant to drain out.
  5. Remove the speedometer driven gear from the upper left rear corner of the case.
  6. Use a suction gun to remove as much lubricant as possible from the case cover location and the speedometer gear location.
  7. Install the speedometer driven gear, the P.T.O. cover, and the lowest bolt or drain plug.
  8. Add approximately seven pints of oil through the filler plug opening. The proper oil to use is 10W-30 or 10W-40 engine oil.
  9. Check the fluid level and add sufficient oil to raise the level to 1 /2 in. below the filler plug opening. Replace the plug, and wipe the surfaces of the case and skid plate to remove any excess oil. Drive the truck and check for leaks.

I really hope help ypou woth this (remember rated this help) Good luck.

Oct 16, 2009 | 1983 Chevrolet Silverado

1 Answer

2000 dodge dakota 4 wheel drive is sliding all over the place


lower linkege not attached

quick easy fix under car

Jul 15, 2009 | 1993 Dodge Dakota

2 Answers

Flat towing 1993 Dodge Dakota 4x4


U MUST remove the remove the drive shaft or u will damage the trans, this is true of all modern cars and trucks, have been doing this 35 years and am 100% sure on this.

May 19, 2009 | 1993 Dodge Dakota

1 Answer

1999 Dodge Durango 4x4 stuck in 4wheel part time


The transfer case shift soleniod that engages the transfer case is sticking .
I would take it to the shop and have it checked out.

Apr 01, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1995 Dodge Dakota Logo

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...