Question about 2005 Hyundai Santa Fe

1 Answer

Replaced power steering pump because it was starting to leak. With new pump no power steering until the engine speed is up and only slightly then. Tried bleeding by turning lock to lock 20 times with no change. Now I did not have the reservoir cap off when I did this, would that prevent it from bleeding or is there another procedure to bleed.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 818 Answers

With the car not running-jack front end up so wheels are off the ground then turn lock to lock-still without motor running-do not let resevoir run out of fluid or it will suck more air in-turning while running will just whip fluid into foam- cheers Denny

Posted on Nov 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1118 Answers

SOURCE: Installed new power steering pump on 2003 Hyundai

Best way i found is to make sure the resavor is full, and start car and turn wheel back and forth lock to lock untill all the air is out of the system or when the noise goes away. Now if there isent a bleeder hole on resavor cap you may have to leave it loose so the air has a place to excape. Be patent it might take a while.

Posted on Apr 04, 2009

emissionwiz
  • 76630 Answers

SOURCE: Power steering fluid is leaking from the cap which

did you overfill the fluid resovior? the cap is vented and provides no seal, so it the tank is overfilled it will bubble out the cap, if the tank is not overfilled you have a defective steering rack that is pulling in air through a defective seal and causing the fluid to foam and bubble out the cap vent.

Posted on Mar 31, 2010

alicantecoli
  • 22219 Answers

SOURCE: How do i bleed the power steering/ I just replaced

just turn left and right a couple of time will do it with engine running

Posted on Oct 22, 2010

c1apton15
  • 3400 Answers

SOURCE: 2006 HYUNDAI Sonata I figured I'd

Try re-bleeding ALL wheels starting with furthest away - pass rear, then driv rear, then pass front and driv front. That should get your pedal back. To reset light you need ABS reset tool and it's EXPENSIVE. Have a good competent shop reset it for you. Body shops can reset them also.

Posted on Feb 27, 2011

DIESELMUDDER
  • 2760 Answers

SOURCE: new power steering pump put in, lines bleed, and still having whinning noise. Is there another part with the power steering pump we can check?

are you sure the noise is comming from pump and not the belt tension pulley right next to it ?

I use a wiffle ball bat with both end caps cut off (hollow tube) held to my ear to help localize noises on running engines I have even found tricky intake vac leaks with that trick

Posted on Apr 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing pump and bleeding power stearing on a 1983 buick riviera


1. Replace any hydraulic line showing external damage. Rubber hoses more than 4 years old should be replaced. Install new seals for all disconnected fittings (as required) and install an in-line power steering filter. Tighten all hose fittings to OE specifications. 2. Flush the entire power steering system using the vehicle manufacturers recommended fluid. Fill pump reservoir to the proper level.
3. Disable engine to allow cranking without starting. This can be done by unplugging the main power wire (large red one) from your Delco HEI Distributor unit. Block wheels, put transmission in neutral or park and set parking brake, then crank engine 5 to 10 seconds (avoid overheating starter motor).
4. Refill pump reservoir as necessary. Repeat step 3 until level is correct.
5. Enable the engine to allow starting. Start engine and let idle. Slowly turn steering wheel from lock to lock a number of times.
6. Turn engine off and inspect fluid level and condition. Add or remove fluid as necessary. If fluid is foaming, wait one hour then recheck level. Repeat step 5 and 6 until fluid level is correct and shows no sign of air. If the problem persists recheck installation and connections.
1. With engine off, apply and release brake pedal 5 to 10 applications to deplete accumulator reserve pressure. With foot slightly pressing brake pedal, start engine. Pedal should drop and then push back against your foot.
2. With engine running, turn steering wheel until lightly against steering stop. After 5 seconds return wheels to the straight ahead position and turn engine off. Apply and release brake pedal. There should be at least one power assisted brake application. Start engine and allow accumulator to recharge before moving vehicle. 3. Test drive vehicle.
NEVER operate any vehicle until brake and booster systems are functioning properly. Remember, your vehicle is only as good as it's braking system. Brakes are the singlemost important component on any motorized vehicle.

Nov 06, 2016 | Buick Cars & Trucks

1 Answer

Very hard to turn steering wheel


Um... the video didn't demonstrate anything, only showed the steering wheel and the key.

If the engine is running, the tires aren't jammed against solid objects, there's no noise from the pump, the belt is tight, the power steering reservoir is full of fluid, and the steering wheel is still very hard to turn... then I suspect that the power steering pump has simply worn out badly and needs to be replaced.

Aug 13, 2014 | Cars & Trucks

1 Answer

Bleed power steering on 2008 dodge avenger


to bleed power steering, with front wheels off ground slightly with front wheels pointing straight ahead.engine off. remove power steering filler cap.add power steering until fluid level stop dropping,wait couple minutes and wait, add fluid until level stay at full cold mark on power steering cap dip stick. dont over fill.when fluid level stop dropping, start vechicle,let it idle few minutes. see if fluid level drop if so add more fluid full cold mark.then turn steering all the way to left and right with out hitting a stop.turn steering wheel several times, then turn front wheels pointing forward check power steering fluid level.if power steering fluid level stop dropping air should be out of system, if steering turning wheel dont turn smoothly and power steering fluid look light tan color air getting in the system.check all power steering lines to rack and power steering pump for leaks.be sure you replaced all the power steering lines with new o rings if not you will get a leak.if you find a leak, you need to fix the leak and bleed system again.dont drive vechicle if your steering dont feel right,have vechicle towed to a garage.

Aug 25, 2012 | 2008 Dodge Avenger

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

3 Answers

Power steering pump replaced, start to work ok, after 10 milles driving, steering wheel is hard, like pump is not working, under hood everything look ok.


YOU HAVE AIR IN THE POWER STEERING SYSTEM.YOU NEED TO BLEED POWER STEERING PUMP FIRST BEFORE DRIVING VECHICLE.CHECK POWER STEERING FLUID LEVEL ADD MORE POWER STEERING UNTIL REACH FULL COLD MARK..RAISE VECHICLE FRONT WHEELS OFF THE GROUND.START ENGINE LET IT IDLE WHILE TURNING STEERING WHEEL LEFT TO RIGHT NON STOP DONT LOCK OR STOP STEERING WHEEL KEEP TURNING IT SEVERAL TIMES CHECK POWER STEERING FLUID IF LOW ADD UNTIL YOU GET COLD MARK ON DIP STICK DONT OVER FILL POWER STEERING PUMP BLOW A SEAL.IF POWER STEERING FLUID LOOK TAN COLOR SYSTEM FULL OF AIR.TURN OFF IGNITION LET CAR SET FOR A WHILE CHECK FLUID LEVEL.IF STEERING WHEEL FEEL STIFF HARD TURNING DONT DRIVE CAR UNTIL YOU HAVE NORMAL STEERING.IF STILL HAVE AIR IN SYSTEM BLEED SYSTEM UNTIL AIR IS OUT.

Feb 25, 2011 | 2002 Chevrolet Avalanche

1 Answer

We have a 2002 motorhome on a P32 Workhorse Chassis. I'm not sure if this is a power steering problem but when turning the wheel at parking speed there is a horrible screeching noise emanating from the...


It's either a loose belt or the pressure regulator inside the pump has failed. I wouldn't leave town until a new power steering pump is installed.

May 10, 2017 | GMC G3500 Cars & Trucks

1 Answer

How to repair a power steering pump hyundai coupe 1996


SIPHON OUT POWER STEERING FLUID.USING A HAND PUMP SIPHON TYPE YOU BUY AT ANY AUTO PARTS STORES.PLACE DRAIN PAN UNDER CAR NEAR POWER STEERING PUMP CATCH FLUID WHEN YOU REMOVE POWER STEERING LINES AT THE PUMP.REMOVE DRIVE BELT.THEN REMOVE POWER STEERING PUMP.YOU NEED TO TAKE OLD PUMP WITH YOU.TAKE NEW PUMP AND OLD PUMP TO MACHINE SHOP THEY WILL REMOVE POWER STEERING PUMP PULLEY FROM THE OLD PUMP TRANSFER PULLEY TO THE NEW POWER STEERING PUMP YOU NEED TO BUY NEW POWER.STEERING HOSES O RINGS TO GO ON NEW POWER STEERING PUMP.HOSES THE OLD ORINGS WILL LEAK. THEN TAKE NEW POWER STEERING PUMP ON INSTALL IN VECHICLE THEN BLEED POWER STEERING SYSTEM.FILL POWER STEERING PUMP UP NEW FLUID.WAIT FEW MINUTES.WHEN LEVEL DROP ADD MORE FLUID UNTIL YOU GET TO FULL COLD MARK.START ENGINE 15 SECONDS SHUT OFF CHECK FOR LEAKS. NOW CHECK POWER STEERING AGAIN ADD TO FULL COLD MARK.NOW RAISE FRONT WHEELS OFF GROUND.START ENGINES TURN STEERING LEFT TO RIGHT WITH OUT STOPPING IT DO SEVERAL TIMES THEN CHECK FLUID.ADD TO THE COLD MARK DONT OVER FILL.IF FLUID LOOKS TAN HAS AIR BUBBLES IN SYSTEM WAIT A WHILE UNTIL FLUID SETTLE CHECK FLUID LEVEL.DONT DRIVE VECHICLE UNTIL STEERING FEELS NORMAL.AND IF YOU HEAR NOISES.LOCATE PROBLEM FIX BEFORE DRIVING VECHICLE.

Jan 24, 2011 | Hyundai Genesis Coupe Cars & Trucks

1 Answer

After I replaced the power steering pump and reservoir on my 2002 Jeep, I still get air in the system. Where could it be coming from?


Your problem could be a pressure side hose that has a rupture that only leaks in extreme conditions. Inspect to replace with new to repair problem. First make sure you have removed the pump caps off of the hose fittings. If ok, it appears you may have a stuck valve in the rack assembly. Replacing the rack should solve your problem. ------- The new pump should be self-bleeding by turning the wheels left and right. Let sit over night to release air bubbles, recheck fluid level.------ Check the tension of the drive belts on the pump, as they may be loose. The power steering pump and reservoir is located on the front of the engine driven by one of the fan belts. There is a removable cap on the top with a dipstick attached. With the engine off, fill this up to the full mark with power steering fluid. Replace the cap, start the engine and check for leaks. On the back of the pump are two hoses either one could be leaking. REPAIR PROCEDURE:
1. Wipe the power steering cap and area free of dirt. Remove the power steering cap.

2. Use a siphon pump to remove as much fluid as possible from the power steering fluid reservoir.

3. With a helper in the vehicle, raise the vehicle on an appropriate hoist.

WARNING :POWER STEERING FLUID, ENGINE PARTS, AND THE EXHAUST SYSTEM MAY BE EXTREMELY HOT IF THE ENGINE HAS BEEN RUNNING. DO NOT START ENGINE WITH ANY LOOSE OR DISCONNECTED HOSES. DO NOT ALLOW HOSES OR POWER STEERING FLUID TO TOUCH HOT EXHAUST MANI FOLD OR CATALYST.
4. Locate the power steering cooler attached to the crossmember support plate. Slide back the clamp and disconnect one of the two power steering return hoses at the power steering oil cooler and drain fluid in an appropriate container.
5. Have the helper turn the steering wheel back and forth quickly several times to force as much fluid as possible from the steering gear.
6. Reconnect the hose at the oil cooler using the original clamp.
7. Lower vehicle so the vehicle tires are not contacting the ground.
9. For proper fluid fill and bleeding air from the power steering system:

a. Fill the power steering reservoir to the top of the fill range using Mopar power steering fluid (ATF+4) p/n 05013458AA.

b. With the engine OFF and the vehicles tires off the ground, slowly turn the steering wheel back and forth (lock to lock) slowly 20 times to force fluid into the steering gear.

c. Fill the power steering reservoir to the top of the fill range.

d. Start engine and let run for a few seconds, then turn oft engine.

e. Check fluid level and add if necessary.

f. Start engine, and slowly turn the steering wheel lightly contacting the left and right stops.

g. Stop the engine and check fluid level. Add fluid if necessary.

h. Lower vehicle, start engine and slowly turn steering wheel lock-to-lock.

I. Stop engine and check fluid level. Add fluid if necessary.

j. If fluid is extremely foamy, allow vehicle to stabilize a few minutes, then repeat steps "i" and "j" until the fluid level remains constant after running the engine and turning the steering wheel from lock to lock.

10. Inform the vehicle owner/operator that a steering vibration may be noted for a few hundred miles until the air is completely removed from the steering system.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Jan 26, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

HOW TO REPLACE A POWER STEERING HOSE


FIRST OF ALL YOU HAVE TO REMOVE POWER STEERING FLUID.USING A SUCTION GUN OR LARGE SYRINGE.REMOVE MUCH FLUID AS POSSIBLE.WHEN DONE REMOVING POWER STEERING FLUID.YOU NEED A INLINE WRENCH AND OPEN BOX END WRENCH TO REMOVE THE POWER STEERING HOSE.YOU HAVE TO REMOVE POWER STEERING LINE FROM THE RACK.UNDER THE CAR SAFELY RAISE AND SUPPORT VECHICLE. THEN REMOVE THE TIRE OR WHEEL.THEN REMOVE THE INNER FENDER SPLASH SHIELD.ITS GOING TO BE A TIGHT FIT AND HARD PLACE TO GET YOUR HAND TO REMOVE THE POWER STEERING LINE FROM BOTTOM.WHEN DONE.MAKE SURE NEW POWER STEERING HOSE OR LINE HAS NEW O RINGS.WHEN INSTALLING THE THE NEW STEERING HOSE.WHEN ALL IS DONE BLEED POWER STEERING SYSTEM. FILL UP POWER STEERING PUMP TO CORRECT FLUID LEVEL.THEN LET IT SET FOR 2 MINUTES UNDISTURBED.THEN START THE ENGINE RUN IT FOR 2 TO 3 SECONDS.ONLY CHECK THE RESERVOIR AND ADD MORE FLUID AS NECESSARY.REPEAT THE OPERATION UNTIL THE FLUID LEVEL REMAIN CONSTANT.NOW RAISE FRONT OF THE CAR UNTIL THE WHEELS CLEAR THE GROUND START THE ENGINE AND INCREASE THE SPEED TO ABOUT 1500 RPM.NOW TURN THE STEERING WHEEL GENTLY FROM STOP TO STOP CHECK THE FLUID LEVEL.LOWER THE VECHICLE TO THE GROUND WITH ENGINE STILL RUNNING MOVE THE CAR FORWARD SUFFICIENTY TO OBTAIN FULL RIGHT LOCK FOLLOWED BY FULL LEFT LOCK BUT DONT HOLD THE SREERING WHEEL FIRMLY AGAINST THE STOPS.RECHECK THE FLUID LEVEL IF THE FLUID IN THE RESERVOIR IS EXTREMELY FOAMY ALLOW THE CAR TO STAND FOR A FEW MINUTES.WITH ENGINE OFF.WHEN JOB IS FINISH. WARNING DONT DRIVE CAR ON ROAD IF YOUR FLUID STILL FOAMY OR POWER STEERING PUMP MAKE NOISES.REBLEED THE SYSTEM AND CHECK FLUID LEVEL AND CHECK FOR LEAKS.DONT DRIVE CAR UNTIL YOU START FEELING NORMAL STEERING.IF YOU HAVE TROUBLE DONT DRIVE.HAVE IT TOWED TO THE NEAREST GARAGE.

Oct 05, 2009 | 1999 Oldsmobile Alero

2 Answers

I HAVE A 93 TOYOTA CAMRY LE V6, THAT HAS A WATER PROBLEM, THE WATER KEEPS GETTING VERY HOT, ENGINE PUSHES THE WATER OUT TO THE COOLANT RESERVOIR, LEAVING MY RADIATOR DRY. I HAVE REPLACED THE THERMOSTAT AND...


These engines will overheat for many reasons. >>make sure there is no leaks at all, as air will cause the system to overheat while losing coolant at the same time. Depending if the radiator is original or after market, there may be TWO radiator caps (one on the engine and one on the radiator)- the one on the engine usually is faulty because of direct engine heat to the seal.>> On the thermostat housing, there is an O-ring at the end of the feeder pipe, usually leaks especially if the thermostat was replaced and not the O-ring. >>Check also the hydraulic driven radiator fan>>Check power steering fluid for proper levels first. unplug the switch atop the powersteering pump, start engine, rev to 2000 rpm (fan should increase in speed-you should hear it) if not it may be faulty.>> Check system for proper flow- With engine cold, remove the engine side radiator cap and rev the engine(1000rpm) slightly, notice if the coolant is flowing. If not, possible faulty pump, or clogged radiator. Hopefully this helps

Sep 18, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...