Question about Cars & Trucks

1 Answer

I have a 1996 VW cabrio & the clutch peddle dropped to the floor. I am able to reach down & pull the clutch toward myself but yet again the peddle when pushed 2 shift goes to floor.... Any suggestions would be very appreciated!!!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 818 Answers

Check the fluid level in the clutch reservoir- Denny

Posted on Nov 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4088 Answers

SOURCE: no pressure clutch pedal goes straight to the floor 1988 holden r

If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Posted on Aug 11, 2009

  • 14 Answers

SOURCE: push gas peddle and once i reach about half

check your TPS throtel position sensor. and the vehicle has a rev limiter so it wont over rev n park and nutral. but thats the first thing i would check do to many TPS's wear out and can get dead spots in them.

Posted on Aug 02, 2009

  • 119 Answers

SOURCE: Clutch pedal goes to the floor(new clutch installed 2 wks ago)

that cable fited one side to cluch pedel and ather side fited gear box side where palte which is relecing clutch bearing. dont forget to adjust.

Posted on Dec 01, 2008

emissionwiz
  • 76630 Answers

SOURCE: 2000 cavalier clutch pedle goes to floor when pushed and stays there, clutch not working no pressure

You are going to have to replace the master and slave cylinders for the hydraulic clutch, the seals have failed in the slave, but from past experience they should always been replaced as a pair.

Posted on Oct 12, 2008

mcalkins3
  • 123 Answers

SOURCE: Clutch pedal goes to the floor, then after pulling it up there is pressure...

There is either air in the system or a leak in the clutch slave cylinder. Check your fluid make sure it is full and the cap is tight.

Posted on Sep 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 vw cabrio idols and revs up. when u pull out or maby go a few yards it will act as if u turned the ign. off or some times when letting clutch out. thanks....


have the OBD codes raed as could be a few different things , i'd guess at crank sensor, air/fuel, but the OBD will be more specific

Oct 24, 2014 | 1999 Volkswagen Cabrio

1 Answer

97 vw jetta, just cranks no fire pushed started help


could be the switch behind the clutch pedal, make sure you are pushing clutch all the way to floor or the switch or wiring issue. Hope it helps is the issue cause thats an easy fix, good luck.

Apr 05, 2013 | 1996 Volkswagen Jetta

1 Answer

I own a 1995 Audi 90cs. My clutch peddle started being dead tell half way down then got preshure. Now there is no preshure and the peddle sticks to the floor. There was no slipping in the clutch so I


You need to replace the clutch slave.....Ii recently did mine, after the installation it was stuck too.......the way I fix it was I had a friend pumping the clutch by hand while I bleed it under the car, it took about 15-20 minutes before it got hard again.
Good luck!

Aug 01, 2012 | 1995 Audi 90

1 Answer

I have a 98 vw passat. about a week ago the clutch went to the floor. i reached down and pulled it back up but again it went to the floor and stayed there. i tried this several times before i took off...


hi,
The problem would be the master clutch cylinder that needed to be replace or the replacement cup kit that must be replace!

Go to ur nearest garage to have the replace it or check on it!

Apr 11, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

I need to get the clutch cable off a 1997 vw cabrio.How do i get the cable off the clutch pedal


After disconnecting the cable from the engine compartment remove the lower panel on the driver side. Press clutch peddle to floor then reach around the steering wheel column on the gas peddle side. you will feel a plastic guard. reach under guard you will feel the cable on top of clutch peddle. pull cable up and toward back of car.

Feb 13, 2011 | 1999 Volkswagen Cabrio

1 Answer

I pressed on the clutch peddle and it snapped to the floor. Its a 96 ford f-150, 6 cyl. 5 speed stndrd. Throw-out bearing?


check your clutch booster fluid be sure to pull the cup out if fluid is low may be bad slave cylinder

Nov 05, 2010 | 1996 Ford F150 Regular Cab

2 Answers

I have a 2001 vw cabrio and the clutch got stuck to the floor and won't come back up, it goes into gear but won't move. i heard it could be the clutch cable, where is this located?


At the top of the pedal, there is a hook that a loop on the cable attaches. It then goes out through the firewall, towards the transaxle, in a half inch think rubber sheath. It then bends down to the front of the transaxle, where it goes though an adjuster and connects to a long arm. Loosen the locking nut and then spin the adjuster so that there is less tension. But is there is no tension, it is not the cable. Then it would be the throwout bearing that was binding. It is under the tailpiece cover. Remove the cover, and operate the clutch to see if the bearing is binding.

Oct 07, 2010 | 1999 Volkswagen Cabrio

2 Answers

Clutch failed ...


the clip hpld the clutch cable to the top of the peddle time to go under the dash let me know post on fixya

May 22, 2009 | 1999 Volkswagen Golf

3 Answers

Clutch peddle goes to the floor


Do you mean that stays to the floor because the clutch peddle has to reach the floor. If that is what you mean then probably you need a knew clutch or if it is hydraulic maybe it reflling and dicomression.

Jan 28, 2009 | 1999 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...