Question about 2007 Mitsubishi Eclipse

1 Answer

Need to calibrate the wiper motor - 2007 Mitsubishi Eclipse

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 2,534 Answers

If the trouble is the wiper is not parking in the right position, I'm afraid it is very likely the motor must be replaced, because most modern cars do not have a transmission like they used to, now the motor is bad if this happens.
Be blessed.

Posted on Nov 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced winshield wiper transmission assembly on 2004 Grand Am and now wipers rest in the middle of winshield. how do i reset calibration so they rest at the bottom


You have to reinstall the wipers when the motor is at park.if the splines don't match up then you have to adjust the transmission assembly

Oct 04, 2017 | Cars & Trucks

1 Answer

I have a 1998 Plymouth voyager and the climate control lights are flashing. I ran a test i found on the internet and got it down to two lights flashing(the ac and the recirculate). I got it to where the...


OK got your message on the other post (About the van) I am assuming that your Voyager is equipped with Automatic Climate Control. Follow the instructions below and you will get a better idea of what is wrong with your system.

Calibration/Diagnostics
1. To enter calibration/diagnostics test, set parking brake. Start and warm engine to normal operating temperature. With engine idling, turn blower switch to high. Turn mode switch to panel. Open all outlets. Move temperature to full cold.
2. Press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (Until ALL LEDs illuminate). All LEDs should illuminate for 5 seconds. Rear wiper and intermittent rear wiper button LEDs will flash alternately during calibration/diagnostics test.
3. After approximately 60 seconds, if only the rear wiper button LED is flashing, calibration is successful and the system is okay. If rear wiper and intermittent rear wiper button LEDs are flashing, Diagnostic Trouble Codes (DTCs) are present. (See "Reading Diagnostic Codes" below)
4. To exit calibration/diagnostics test at any time, press the rear window defogger button, rear wiper button, or cycle the ignition off and then on. Test will automatically terminate 15 minutes after calibration/diagnostics is entered.

Reading Diagnostic Codes
1. Perform calibration/diagnostics test. If a DTC is present after calibration/diagnostics test has been performed, system will flash rear wiper and intermittent rear wiper button LEDs in sequence. Rear wiper represents code level, and intermittent rear wiper button LED represents code value.
2. Each time the rear wash button is depressed, rear wiper button LED wil cycle to the next code level in numeric sequence. After code level 5 is reached, rear wiper button LED will cycle back to code level 1. See table below.

dttech_67.gif

May 12, 2011 | Plymouth Voyager Cars & Trucks

1 Answer

I have a 1997 plymouth grand voyager. Everything was working fine until my battery died. Replaced battery & now my rear window wiper lights on the dash blink constantly. The wipers work fine when I cut...


What has most likely happened is that the Heater-a/c unit needs to be recalibrated and here are the steps to do so.
With the engine running and fully warmed up, A/C has to be turned off for at least 5 minutes [don't turn it on at all] and transmission in Park do the following
1. Set the temp control all the way to cold
2. Set the mode selector to Vent so air blows out of the dash panel outlets.
3. Hold down the rear washer button and the rear wiper buttons simultaineously for about 5 seconds until most all of the heater and ac panel lights blink and then release both buttons
6. At this point the system should go into a self calibration test which can take up to 60 seconds. While it is calibrating various control panel switch lights will blink as it goes through it's tests.
7. When the system is done calibrating then just the rear wiper light should be flashing and you can exit the test by turning off the vehicle. Wait about 10 seconds and restart the engine and it should be fine. If both the rear wiper and intermittent light are both still flashing after the calibration then there is most likely a problem with the system that will need more diagnosing. I see this fairly often with battery replacements so I think you'll be ok. It sometimes takes a couple of tries to calibrate so don't give up if it doesn't work the first time. Good luck, hope this helps!

Jul 14, 2010 | 1997 Plymouth Grand Voyager

3 Answers

1998 dodge caravan. AC problem. My AC doesnt work, the lights on the dash are blinking. I took the Van to C-Tire to get the AC recharged as the AC clutch was not turn when the van is running. C-tire did a...


do this calibration reset, it will usually rest he lights and the ac will work again, if it doesn't reset you have a part failure and the dealer you need to hook a Chrysler scan tool to diagnose the problem.

CALIBRATION/DIAGNOSTICS TEST ENTRY
TO INITIATE TESTS:
Set Blower motor ON HIGH
Set Mode position to Panel
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)
RESULTS:
All LED's will turn on for 5 Seconds
Calibration Test is running when REAR WIPER and INTERMITTENT are alternately flashing. Cooldown test is running if A/C and RECIRC are alternately flashing.
Acceptable results is REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit.
After all tests have passed, Calibration Diagnostics and Cooldown can be run separately

Jul 26, 2009 | 1998 Dodge Caravan

2 Answers

Blinking panel button lights


That has to do with your computer for your body controls, such a/c, heater, wipers, etc...
Most common problem is drinks spilling into the computer which is right between the cup holder. It will eventually cause a problem with a/c most likely.

Jun 24, 2009 | 1998 Dodge Caravan

1 Answer

Calibrating the heat and air conditioning control module


Hold the rear wiper button and the rear wiper wash buton for like 4-5 sec and it will start its calibration i think you need the blower on hi and the temperature knob at cold

Feb 22, 2009 | 1996 Dodge Caravan

1 Answer

Wipers


the climate control panel has come out of calibration..
to re-calibrate it you need to have
Set Blower motor ON HIGH
Set Mode position to Panel
Open all A/C outlets
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)

All LED's will turn on for 5 Seconds
When done REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit

your a/c system must be functioning properly for it to re-calibrate.

Sep 10, 2008 | 1997 Chrysler Town & Country

1 Answer

Dodge Caravan 2003 airbag and engine light


Sounds like the HVAC control head needs to be recalibrated. The procedure is fairly easy, Heres how its done:

CALIBRATION/DIAGNOSTICS TEST ENTRY
TO INITIATE TESTS:
Set Blower motor ON HIGH
Set Mode position to Panel
Set Temperature to Cold (Both slide pots if equipped)
Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light)
RESULTS:
All LED's will turn on for 5 Seconds
Calibration Test is running when REAR WIPER and INTERMITTENT are alternately flashing. Cooldown test is running if A/C and RECIRC are alternately flashing.
Acceptable results is REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit.
After all tests have passed, Calibration Diagnostics and Cooldown can be run separately.

After that the lights should go out and everything should work properly as long as everything is in proper working order.

Good Luck

Aug 25, 2008 | 2003 Dodge Caravan

Not finding what you are looking for?
2007 Mitsubishi Eclipse Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...