Question about 2004 Chrysler 300M
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: AC belt on 1999 Chrysler 300M
When you replace the AC belt you really should replace the serpentine belt as well, since you will have to take it off already. If you don't do it now it is inevitable that you will have to replace it in like 3 weeks anyway : )
You need to first remove the serpentine belt by loosening the nut in the center of the idler pulley. After that you will need to loosen the push bolt on the side of the idler pulley. The hub bolt is a 15mm size and the push bolt on the side of the tensioner is a 13mm I think. After you loosen it sufficiently, you will need to pull off the old belt.
Next you will need to loosen the tensioner pulley for the AC belt as well. It is the same process. The main issue is space. You will most likely need to raise your car to get at the right angles to loosen these pulleys.
Once you loosen the idler pulley in the same manner as you loosened the other, you can slip the AC belt onto the back of the crank pulley and route it as the diagram under your hood instructs you. Next tighten up the idler pully in the opposite way as you loosend it...tighten up the push bolt until the belt play is within factory specifications, then tighten the hub bolt in the center of the pulley. Do the same for the serpentine belt and you should be up and running in no time. I just performed these tasks on my 2000 300m and I wish someone would have told me this before I started my project. Hope this helps, Good Luck!
Posted on May 26, 2009
Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When programming is complete, the door locks will cycle once.
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.
6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.
Posted on Jun 25, 2009
Look above your brake pedal and you will see your brake switch up along your brake pedal arm. It will either be between the brake arm and the firewall so when you brake it pushes the switch in. Or it will be between the dash and the brake arm so when you brake it pulls the switch out. Most likely this switch needs to be replaced
Posted on Oct 23, 2009
Tips for a great answer:
Jul 14, 2014 | 2003 Chrysler 300M
Aug 02, 2012 | 2003 Chrysler 300M
May 09, 2011 | 2003 Chrysler 300M
Jan 28, 2011 | 2003 Chrysler 300M
Sep 18, 2009 | 2003 Chrysler 300M
Jan 28, 2009 | 2003 Chrysler 300M
Mar 09, 2015 | 2004 Chrysler 300M
34 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: