Question about 2002 Toyota Celica

Open Question

Diagram engine Does anyone have a diagram of all the water hoses on a 02 celiac gt 1.8

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for cooling system bleeder valve 02 deville


There isn't one !
Filling Procedure
Notice: Do not add cold water to the cooling system with the engine at or above operating temperature. Adding cold water causes rapid cooling, resulting in possible engine damage.
NOTICE: When adding coolant, it is important that you use GM Goodwrench DEX-COOL® or HAVOLINE® DEX-COOL® coolant. If Coolant other than DEX-COOL® or HAVOLINE® DEX-COOL® is added to the system the engine coolant will require change sooner; at 50 000 km (30,000 mi) or 24 months.
Notice: Do not use a solution stronger than 70 percent antifreeze. Pure antifreeze can freeze at -22°C (-8°F).
Important: This engine is not equipped with block drains, 2.5 L (2 qt) of residual coolant remains in the engine block.
Refill the cooling system. In order to ensure sufficient engine cooling, freezing and corrosion protection, maintain the protection level at -37°C (-34°F) or lower.
Start the engine.
Place the heater and A/C control in any A/C mode except Max and the temperature in the highest setting.
Allow the engine to continue idling until the lower radiator to water pump hose is hot.
Turn OFF the engine.
Allow the engine to cool to outside temperature. Ensure the coolant level in the surge tank is at the proper level (1).

Nov 19, 2016 | 2002 Cadillac Deville

1 Answer

Where is the water radiator in 2000 Toyota celiac


normally just behind the grill before the engine

Mar 14, 2016 | 2000 Toyota Celica

1 Answer

Vacuum hose routing 2002 Suzuki 2.0L


my guess engine plenum vacuum. J20 engine.

ill now take a wild guess that its not axle vents and and washer
you said vacuum but how would you know that if its not connected?
X >>>>>> Z
do tell which end is connected and to what.?
so ill answer for vacuum only

first off , if in USA, the under hood EPA mandated vacuum map
is in full view, ever look there?
if not in USA, all answers are wrong. as they run different EFI , outside USA. (canada?)
page 20 and 27
http://www.fixkick.com/engine/20Liter/html/index.html


this engine has almost no vacuum lines (for sure gone is EGR mess)
Brake booster (huge hose)
Fuel pressure reg.
EVAP hoses. from engine to gas tank.
PCV hose

click add photo and add it , and all guessing ends, for sure.

Nov 08, 2014 | Suzuki Cars & Trucks

2 Answers

Engine Diagrams


Hello. Here a non-photo diagram. Hope this helps!!!

The thermostat is located on the side of the water pump, the water pump is located just above the a/c compressor, the thermostat is fed coolant from the radiators lower radiator hose.
Thermostat :
1. drain coolant and tighten drain plug ( easier method : remove radiator cap, get big drain pan, place drain pan under lower radiator hose to radiator connection, remove clamp, slowly remove hose, allow coolant to drain into pan, now is a good time to remove radiator hose and clamp from thermostat housing )
2. remove thermostat cover / cap ( easiest to get at this when front of car is supported by jack stands and right hand side lower cover is removed ).
3. thermostat cap is held on by 3 bolts / remove thermostat.

You will notice that the thermostat's air bleed hole is pointing up and lines up with notch in water pump housing,,

ATTENTION :failure to install new thermostat in the correct location will cause engine to overheat.

1. install new thermostat to water pump, make sure air bleed hole lines up with notch, install and tighten bolts, install a new lower radiator hose, fill cooling system.

thermostat # 17670-77E00
lower radiator hose #17854-65G20
hose clamp #09401-36403
upper radiator hose # 17852-65G20

Suzuki factory manual

Oct 21, 2013 | Cars & Trucks

1 Answer

I have a hose leaking water it is located just below the connection of the lower radiator hose at the connections of the engine - i need to replace the hose and its in a very hard to reach spot - what is...


FWD car blues...... what engine option?
if you cant reach the clamps with simple accesory parts removal.
then its FWD blues. front wheel drive, ,
id say check the FSM. or alldata.com for how to do this.
there is no magic here, how to reach things, depends on persons size too. so.?????
did you look under the fender for access plates? behind tire>

the parts list on line at honda tell you the names
ever look there, water hose. bypass, heater, etc.>>>.

on some cars some hose are very hard to replace.
some even need the alternator pulled. or other parts .
for sure not the whole engine.

there are only 6 hose (water) small on the engine
3 bypass hose below the Throttle body. &1 at middle of long pipe.
long steel water manifold. pipe.
and 1 larger at from block to heater valve
and 2 larger going to , heater,

did you ever click , the water hose name here?
http://www.realhondaparts.com/rwhonda/jsp/prddisplay.jsp?inputstate=5&catcgry1=ACCORD&catcgry2=1995&catcgry3=2DR+EX&catcgry4=KA4AT&catcgry5=WATER+HOSE+%28+95-97%29&ListAll=All&vinsrch=no&systemcomp=Engine&vinnoT=&trim=&trans=&view=normal

Sep 24, 2013 | 1995 Honda Accord

1 Answer

Can you find an engine diagram for an 02 chevy


That is the water pump bypass/heater hoses you have to get them from the dealer, they know the ones. They are plastic and you should replace both and make sure you get all the pieces out as they will break when removed.

Aug 02, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

Removal and installation of the water pump


3.0L or 3.8L engine?

please rate as fixed if this solves your issue.

Section 03-01B: Engine, 3.8L 1996 Windstar Workshop Manual
IN-VEHICLE SERVICE Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
  1. Drain engine cooling system. Refer to Section 03-03 .
  1. Loosen drive belt tensioner (6B209) and remove drive belt (8620). Refer to Section 03-05 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Disconnect lower radiator hose (8286) from radiator lower hose tube (8291) and radiator (8005).
  1. Disconnect radiator lower hose tube from water pump (8501).
  1. Remove lower nut on both front engine support insulators (6038).
  1. Lower vehicle.
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove generator (GEN) (10346) from power steering pump support (3C511).
  1. Position drain pan and disconnect power steering pressure line from power steering pump (3A674) using Fuel Line Disconnect Tool Set T90T-9550-S.
  1. Remove power steering reservoir filler cap.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces.
    Disconnect water bypass hose (8597) and oil cooler hose (6B850) from heater water outlet tube (18663).
  1. Remove retaining bolts and disconnect heater water outlet tube from water pump.
  1. Remove A/C bracket brace.
  1. Attach engine lifting eye to left-hand (front) exhaust manifold (9430).
  1. Attach lifting equipment to engine lifting eye and raise front of engine approximately 51 mm (2.0 inches) to provide necessary clearance for water pump removal.
  1. Remove water pump pulley retaining bolts and water pump pulley (8509).
  1. Remove drive belt tensioner pulley retaining bolt and drive belt tensioner pulley (6B217) from power steering pump support.
  1. Remove power steering pump support retaining bolts and nut. Place power steering pump and support assembly aside in a position to prevent fluid leakage.
  1. Remove water pump retaining bolts and nuts and water pump. Discard used water pump housing gasket (8507).
Installation
  1. NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant.

    Clean gasket surfaces on water pump and engine front cover (6019).
  1. NOTE: The threads of the No. 1 engine front cover retaining stud must be coated with Pipe Sealant with Teflon® D8AZ-19554-A or equivalent meeting Ford specification WSK-M2G350-A2 before installing.

    NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the water pump housing gasket in position.

    Position a new water pump housing gasket on water pump housing sealing surface.
  1. Position water pump on the engine front cover. Install retaining bolts.
  1. Position power steering pump support and install retaining nuts and bolts. Tighten bolts and nuts to 40-55 Nm (30-40 lb-ft).
  1. Install drive belt tensioner pulley and retaining bolt. Tighten bolt to 70-95 Nm (52-70 lb-ft).
  1. Install A/C bracket brace.
  1. Position water pump pulley on water pump hub and install retaining bolts. Tighten bolts to 8.0-11.5 Nm (71-101 lb-in).
  1. Lower engine and disconnect lifting equipment from lifting eye.
  1. Remove lifting eye from exhaust manifold.
  1. Connect heater water outlet tube to water pump and install retaining bolts. Tighten bolts to 8-11.5 Nm (71-101 lb-in).
  1. Connect water bypass hose and oil cooler hose to heater water outlet tube. Tighten clamps securely.
  1. Connect power steering pressure line to power steering pump fitting.
  1. Install power steering reservoir filler cap.
  1. Install generator to power steering pump support. Refer to Section 14-02 .
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Install lower nut on front engine support insulators and tighten retaining nut to 88-119 Nm (65-87 lb-ft). Install lower nut of rear engine support insulator and tighten to 77-104 Nm (56-76 lb-ft).
  1. Connect radiator lower hose tube to water pump. Install retaining bolt and tighten securely.
  1. Connect lower radiator hose to radiator lower hose tube and radiator. Position hose clamps securely. Refer to Section 03-03 .
  1. Lower vehicle.
  1. Position drive belt over drive belt tensioner and release drive belt tensioner. Refer to Section 03-05 .
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: This engine has aluminum cylinder heads (6049) and requires a special corrosion inhibiting coolant to avoid cooling system damage. Refer to Section 03-03 for the coolant specifications.
    Fill and bleed cooling system with specified coolant.
  1. Fill power steering pump reservoir with specified fluid.
  1. Start engine and check for coolant and power steering fluid leaks. Service as necessary.


    Water Pump
581f50d.gif

Apr 13, 2009 | 1996 Ford Windstar

Not finding what you are looking for?
2002 Toyota Celica Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...