Question about Cars & Trucks

1 Answer

Program garage door opener kia - Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 20 Answers

Go to the homelink website, they have videos and instruction

Posted on Jan 19, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1348 Answers

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

Posted on May 14, 2009

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

  • 1 Answer

SOURCE: programming the garage door opener

Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Program garage door oopener on 2003 KIA Sedona


THE INSTRUCTIONS SHOULD BE IN YOUR OWNERS MANUAL.

IF YOU DON'T HAVE ONE GOTO HOMELINK.COM
THEY MAKE THE VISOR SYSTEMS AND HAVE INSTRUCTIONS POSTED ON HOW TO PROGRAM.

FOLLOW STEPS CAREFULLY.

NOTE: NOT ALL OPENERS CAN BE PROGRAMED TO WORK WITH THESE SYSTEMS.

HOPE THIS HELPS

May 10, 2010 | 2003 Kia Sedona

Tip

2010 BMW 528XI Garage Door Opener Homelink Setup


**** >>> This setup I performed with my new 2010 BMW 528XI Garage Door Homelink and Chamberlain Garage Door Opener <<< ****

Chamberlain:
01. Power off or unplug the garage door opener motor power supply (which is mounted on ceiling of the garage) ;;;

02. keep the garage door opener transmitter in your hand (do not press any button at this time) ;;;

03. In your 2010 BMW 528XI Homelink button (which resides under rear view mirror) press the 1st and 3rd homelink button together for about 30-40 seconds (i.e., until the yellow light blinks fast) and when the yellow light next to the homelink button blinks fast release from pressing the (homelink) buttons ;;;

04. now hold the garage door opener transmitter closer (means within 2-4 inches) to the homelink button (either 1st or 2nd or 3rd) whichever you are planning to program to open the garage door ;;;

05. now press the garage door opener transmitter button and chosen homelink button (either 1st or 2nd or 3rd whatever you need) together ;;;

06. the yellow light (next to homelink button) initially may blink slowly but after few seconds (may be 10-20 seconds) will blink fast; once it started blinking fast release from pressing both garage door opener transmitter and homelink button ;;;

07. Now plug or power on the main garage door opener motor (which is mounted on garage ceiling) ;;;

08. On the main garage door opener motor (which is mounted on garage ceiling) press the "LEARN" button (once you press it may have yellow/orange color light; make sure the light is on) ; then within 30 seconds do the next steps #9, #10, #11 very carefully ;;;

09. go to your car and press the homelink button you programmed and hold it for 4 seconds and then release it --> 1st iteration ;;;

10. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 2nd iteration ;;;

11. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 3rd iteration ** important note; generally three iterations are not necessary; and steps #9, #10, #11 must be performed within 30 seconds ** ;;;

12. during one of the iteration you will hear "CLICK" sound one-time from Garage door motor (which is mounted on ceiling) and if you have light attached with it; it will blink once (** if you hear the CLICK sound and/or light blinks once**) then the particular homelink button is programmed ;;;

13. now press the programmed homelink button; the garage door will open or close (but always it will take 3 or 4 blinks in yellow light or 2-3 seconds before the garage door opens or closes and which is normal) ;;;

** Thats it, your 2010 BMW 528XI Garage Door Opener Homelink setup is complete ** ;;;

You can program rest of the homelink button the same way but following from the steps between #4 and #13 ;;;

Hope this steps will help you to program chamberlain Garage door opener in 2010 BMW 528XI Homelink. ;;;


** possibly the above same steps may work with other BMW 5-series cars homelink too (but I'm not sure) **

on May 29, 2010 | BMW 528 Cars & Trucks

1 Answer

Garage door opener on review mirror


GO TO HOMELINK.COM FOR PROGRAMING INSTRUCTIONS AND A LIST OF DOOR OPENERS THAT THIS WILL WORK WITH.

May 03, 2010 | 2006 Kia Optima

1 Answer

HOW DO I PROGRAM MY GARAGE DOOR OPENER IN THE REAR VIEW MIRROR OF MY 2007 KIA SORRENTO


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: MOST BUT NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Feb 08, 2010 | 2004 Kia Sorento

1 Answer

How do I program the garage door opener that is built into my rearview mirror?


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Jan 31, 2010 | 2004 Kia Sorento

1 Answer

How do I program the garage door opener in the overhead console of my Kia?


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Dec 21, 2009 | 2003 Kia Sedona

1 Answer

How do I program my Genie garage door opener to my 2005 Kia


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Oct 16, 2009 | 2005 Kia Sorento

1 Answer

Program 2004 mercury mountainer garage opener


Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.

Apr 01, 2009 | 2004 Mercury Mountaineer

1 Answer

Garage door button programimg


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Mar 15, 2009 | 2006 Kia Amanti

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...