Question about Cars & Trucks

Open Question

Assembly instructions for Texsport 02820 screen house

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fit a side front off side bulb in my 2002 ford escort van diesel 55


Instructions
  1. Make sure the the headlight switch is in the off position.
  2. Open the bonnet to the Escort.
  3. Locate the back side of the headlight assembly to the headlight that needs to be changed (driver's side or passenger side) from inside the front the engine compartment.
  4. Unplug the wires from the back of the bulb.
  5. Turn the back of the bulb housing counterclockwise one-third of a turn until the bulb and wire harness are released from the headlight assembly.
  6. Unplug the wire harness from the bulb socket.
  7. If using Halogen headlight replacement and be careful not to touch the glass bulb part. Handle it by the socket at the bottom of the headlight.
  8. Plug the wire harness into the new headlight replacement.
  9. Align the tabs on the headlight housing to the slots in the headlight assembly and insert the bulb into the assembly. Twist the headlight one-third of a turn clockwise until it locks into place.

Dec 03, 2014 | Ford Cars & Trucks

1 Answer

I need to setup my texsport patriot arbor


Hi William, I believe you may be in the wrong forum? Regards John

Sep 01, 2012 | Cars & Trucks

1 Answer

Texsport Valley Falls tent manual


You have this posted in the wrong product category

Jun 10, 2012 | Cars & Trucks

1 Answer

Need to replace drivers side mirror assembly, could use a diagram or instructions.


there is probably a small cover on the 'back' part of the mmirror housing, by the corner front part of the window/door=pry it back, it will expose small bolts/screws that hold the housing to the door.

Dec 23, 2010 | 2006 Toyota Corolla

1 Answer

L200 Saturn 2002. Where is the blower fan located for the heat and ac?


It's in the engine compartment. See removal instructions below from autozone.com.

  1. Select the following settings:

    Turn the ignition ON Select Recirc in the OFF setting Turn the ignition OFF
  2. Disconnect the negative battery cable.
  3. Remove the wiper arm assemblies.
    CAUTION A sharp edge is revealed once the weatherstrip is removed.
  4. Remove the weatherstrip at rear of the engine compartment.
  5. Remove the cowl retaining nuts.

jturcotte_564.gif Fig. Remove the cowl screen assembly
  1. Remove the cowl screen assembly.
  2. Rotate the locking tabs outward to release the filter assembly.
  3. Remove the filter by lifting straight up.
jturcotte_567.gif Fig. Remove the wiper module retaining bolts
  1. Remove the wiper module retaining bolts.
  2. Reposition the wiper module to the right.
  3. Remove the filter housing attachment bolts.
  4. Remove the filter housing.
  5. Remove the blower motor housing:
  6. Remove the blower motor housing screws

jturcotte_568.gif
Fig. Release the locking tabs and remove the fan housing
  1. Release the locking tabs and remove the fan housing
  2. Disconnect the blower motor electrical connector.
  3. Squeeze the bottom of the connector and pull downward.
  4. Remove the blower motor assembly by lifting straight out.

Dec 20, 2010 | 2002 Saturn L-Series

1 Answer

Problem with dual zone heating only one side i check control thermost botton is ok


Sounds like the blend door actuator. It separates the driver and passenger side from getting air on the AZC system. Here are some instructions on replacing it:
The passenger side blend door actuator is used on all models equipped with Automatic Zone Control (AZC). This actuator is located on the front of the HVAC housing to the right of the floor panel transmission tunnel and cannot be removed from the passenger compartment without instrument panel or HVAC housing removal.

NOTE: This procedure is for AZC Systems (Passenger side only).

  1. Disconnect and isolate the battery negative cable.
  2. Remove the glove box door. See: Body and Frame\Interior Moulding / Trim
  3. Remove the lower I/P glove box door surround panel.
  4. Remove the dash assembly. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Remove the HVAC assembly. See: Housing Assembly HVAC\Service and Repair
  6. Unplug the wire harness connector from the blend door actuator.
  7. Remove the 2 screws that secure the blend door actuator to the HVAC housing.
  8. Remove the blend door actuator from the HVAC housing.
INSTALLATION - AZC (Passenger side only)


  1. In stall the blend door actuator on the HVAC housing and tighten the two mounting screws to 2.2 Nm (20 in. lbs.).
  2. Plug in the wire harness connector to the blend door actuator.
  3. In stall the HVAC unit into the vehicle. See: Housing Assembly HVAC\Service and Repair
  4. Install the instrument panel assembly into the vehicle. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Evacuate the HVAC system.
  6. Recharge the HVAC system.
  7. Connect and the battery negative cable.
Hope it helps! If you need more, just send me an email at familyguy77351 at yah I wil be glad to finish helping you with more detail.

Dec 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Replacing Thermostat Where is it ?


It's under the housing shown below on the back side of the engine. Instructions taken from autozone.com. I recommend you also read my post at http://www.fixya.com/cars/r5929960-s_thermostat and let me know if you have any questions.

3.1L Engine

  1. Disconnect the negative battery cable.
  2. Drain the cooling system, into a suitable container, to a level below the thermostat housing.
  3. Remove the air cleaner assembly.
  4. Remove thermostat housing-to-intake manifold attaching bolt and nut, then remove the housing.

jturcotte_424.gif

Fig. Remove the two housing-to-intake manifold bolts and remove the housing

  1. Remove the thermostat.

To install:
  1. Clean all gasket surfaces completely.
  2. Insert the thermostat in the intake manifold.
  3. Attach the thermostat housing to the intake manifold.
  4. Install the mounting bolt and nut. Tighten to 18 ft. lbs. (25 Nm)
  5. Install the air cleaner assembly.
  6. Connect the surge tank line to thermostat housing.
  7. Refill the cooling system.
  8. Connect the negative battery cable, remove the radiator cap, then start the engine. Allow the engine to run with radiator cap removed, until the upper radiator hose becomes hot (thermostat open). With the engine idling, add coolant to the radiator until the level is up to the bottom of the filler neck.
  9. Install the radiator cap, making sure the arrows line up with the overflow tube.

Dec 08, 2010 | 2000 Chevrolet Malibu

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

How to remove and install a new heater blower motor 2000 Saturn


Removal & Installation
  1. Select the following settings:
    Turn the ignition ON Select Recirc in the OFF setting Turn the ignition OFF
  2. Disconnect the negative battery cable.
  3. Remove the wiper arm assemblies.
    CAUTION A sharp edge is revealed once the weatherstrip is removed.
  4. Remove the weatherstrip at rear of the engine compartment.
  5. Remove the cowl retaining nuts.

    7f880eb.jpg

    Fig. Remove the cowl screen assembly

  6. Remove the cowl screen assembly.
  7. Rotate the locking tabs outward to release the filter assembly.
  8. Remove the filter by lifting straight up.

    3f001dc.jpg

    Fig. Remove the wiper module retaining bolts

  9. Remove the wiper module retaining bolts.
  10. Reposition the wiper module to the right.
  11. Remove the filter housing attachment bolts.
  12. Remove the filter housing.
  13. Remove the blower motor housing:
  14. Remove the blower motor housing screws

    855cd3a.jpg

    Fig. Release the locking tabs and remove the fan housing

  15. Release the locking tabs and remove the fan housing
  16. Disconnect the blower motor electrical connector.
  17. Squeeze the bottom of the connector and pull downward.
  18. Remove the blower motor assembly by lifting straight out.
To install:

NOTE The fan motor assembly rib must be located into the channel in the module housing.
  1. Install the blower motor assembly into the module housing.
  2. Connect the blower motor electrical connector.
    NOTE The housing rib must fit into the slot in the HVAC module case.
  3. Install the blower motor housing. Snap the left and right clip into place
  4. Tighten the fan housing to blower motor housing screws to 9 inch lbs.(1 Nm).
    NOTE A new filter housing seal must be used whenever the filter housing is removed to prevent water from leaking into module.
  5. Remove the filter housing seal using a small flat-blade screwdriver.
  6. Install a new filter housing seal.
  7. Install the filter housing.
  8. Install the filter housing screws, and tighten the screws to 31 inch lbs.(3.5 Nm).
  9. Position the wiper module.
  10. Install the wiper module bolts, and tighten the bolts to 44 inch lbs.(5 Nm).
  11. Install the passenger compartment air filter. Notice the air flow direction indicator printed on side of the filter.
  12. Rotate the locking tabs on the filter housing inward to secure the air filter in place.
  13. Install the cowl screen.
  14. Install the cowl screen nuts, and tighten the nuts to 9 inch lbs.(1 Nm).
  15. Close filter access door.
  16. Install the weatherstrip at rear of the engine compartment.
  17. Install the wiper arm assemblies.
  18. Connect the negative battery cable.
  1. Disconnect the blower motor electrical connector.
  2. Remove the lower blower motor cover retaining screws.

    dadd8a2.jpg

    Fig. Remove the lower blower motor cover

  3. Remove the lower blower motor cover.
  4. Remove the blower motor nuts.
    NOTE Cut through the case as straight as possible because the motor cup must be replaced.
  5. In order to prevent damage to the component, do not cut any deeper than necessary to remove the motor cup.
  6. Remove the blower motor and cup from the lower case by cutting through the case between the circular ribs around the motor with a sharp utility knife.
  7. Release the blower motor retaining tab and remove the motor from the cup.
To install:
  1. Install the blower motor into the motor cup that was cut out of the lower case.

    bc83072.jpg

    Fig. Install the blower motor (1) into the motor cup (2) that was cut out of the lower case

  2. Install the blower motor nuts, and tighten the nuts to 21 inch lbs.(2.4 Nm).
  3. Attach the service ring to the motor cup with the screws included in the kit, and tighten the screws to 15 inch lbs.(1.8 Nm).
  4. Install the blower motor and service ring into the HVAC module using the screws included in the kit. Make certain the blower motor electrical connector is pointing rearward in the vehicle, and tighten the screws to 15 inch lbs.(1.8 Nm).
  5. Install the lower blower motor cover.
  6. Install the lower blower motor cover retaining screws, and tighten the screws to 15 inch lbs.(1.8 Nm).
  7. Connect the blower motor electrical connector.

Hope this helps (remember to rate and comment this).

Oct 04, 2010 | 2000 Saturn Ls 4dr Sedan

1 Answer

I need to know how to get to the blower fan as it is not kicking on/blowing any heat/ air and my manual does not say where it is located and how to get to it.


I will paste instruction from autozone.com below. Also, check my solution at http://www.fixya.com/cars/t6104871-heater_fan_just_quit_working_find_fuse.

  1. Disconnect the negative battery cable.
  2. Remove the glove box assembly, lower right side instrument panel trim cover and right cowl trim panel, as required. Disconnect the blower lead wire connector.
  3. If the vehicle is equipped with air conditioning, disconnect the 2 vacuum lines from the recirculating door actuator and position the actuator aside.




0900c152802686b4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Blower motor housing cover



0900c152802686b5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Blower motor and wheel assembly



0900c152802686b6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the spring-type retaining clip to separate the wheel from the blower motor

  1. Remove the 2 screws at the top of the blower housing that secure it to the unit cover.
  2. Remove the 5 screws from around the blower housing and separate the blower housing from the unit.
  3. Remove the 3 screws that secure the blower assembly to the heater or air conditioning housing and remove the assembly from the unit. Remove the fan from the blower motor by removing the spring-type retaining ring from the center of the blower wheel. Note the location of the fan-to-blower motor assembly for correct installation.




0900c152802686b7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: To gain access to the blower motor, unplug the electrical connectors from the glove box lamp, ...



0900c152802686b8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: ... then remove the glove box assembly from the dash panel

Sep 21, 2010 | 1989 Chrysler New Yorker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...