Question about 1997 Nissan Maxima
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
gadiame: The code P1400 is for the EGR valve and Evap canister purge control solenoid valve circuit.
An improper voltage signal is being sent to the ECM through the solenoid valve.
As far as whether the engine using a timing belt or gear? You mean chain? This engine uses a timing chain.
If I can answer any other questions, write me.
Posted on Apr 07, 2009
P1400 on your vehicle is described as :Differential Pressure Feedback EGR Circuit Low Input You either need a new DPFE valve, or a new EGR valve. Both can be tested for functionality before replacing them both. EGR valve is more likely I think. Cleaning it may not improve its performance, but its worth a try. Also check the vacuum lines between the DPFE and EGR system. The EGR valve and DPFE are usually close together above the exhaust manifold/downpipe. you need service instructions to test these items, suggest you go to a garage really...
Posted on May 17, 2009
SOURCE: 97 Nissan Maxima OBDll code
The code p1400, is for an egrc solenoid valve, not the egr valve, they are 2 seperate items
exhaust-gas recirculation (EGR): An emissions-control system that reduces an engine's production of oxides of nitrogen by diluting the air/fuel mixture with exhaust gas so that peak combustion temperatures in the cylinders are lowered.
exhaust-gas recirculation valve (EGR valve): A valve, generally vacuum operated, to regulate the exhaust gas flow into the intake manifold.
EGR control solenoid (EGRC): receives ported and manifold vacuum, an EGR temperature sensor and a control backpressure transducer valve. THE operation of the system is controlled by the PCM which operates the EGRC solenoid. The manifold vacuum system utilizes a vacuum tap in the air intake system positioned after the throttle valve. The ported vacuum control system uses a vacuum tap in the throttle body which is exposed to an increasing percentage of manifold vacuum as the throttle valve is opened during acceleration. The backpressure transducer valve monitors the exhaust backpressure as the engine rpm increases or decreases to aid in controlling the amount of the EGR vacuum signal. The EGR temperature sensor is used to inform the PCM of temperature changes in the EGR passage way. This helps the PCM determine the EGR on/off time.
that should help on what they all do.
now by knowing all of that i highly doubt that the control solenoid could cause the problem, and if it was that then u probably have a PCM problem not the solenoid or both.P01400 generally means that the ECM is not seeing the correct voltage drop when it grounds the EGRC valve located between the banks of CLY'S near the top Radiator hose location the EGRC solenoid valve turns vacuum on to the EGR circuit or vents. With a OHM meter unplug the EGRC valve and measure resistance at the two pins. Most likely your car has a bad EGRC valve or a BAD wire to it from the engine control module. Valve Nissan Dealership would cost around $45 labor to diagnosis and replace $150. Make sure proper diagnosis is performed check the engine wiring harness with a stop lamp light bulb hooked to the EGRC connector to see if it lights up when driving. That way you know the circuit is ok. A engine harness with a open circuit is a bad surprise after spending $200 for the valve. Good Luck
Posted on Oct 08, 2010
Tips for a great answer:
Feb 16, 2017 | Nissan Cars & Trucks
Aug 31, 2014 | 1995 Nissan Maxima
Aug 17, 2013 | 1997 Nissan Maxima
Oct 23, 2010 | 1995 Nissan Maxima
Jan 19, 2009 | 1997 Nissan Maxima
Jun 08, 2008 | 1997 Nissan.5 Altima
48 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: