Question about 1987 Chevrolet Celebrity

1 Answer

Brake tools - 1987 Chevrolet Celebrity

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Chevrolet Expert
  • 495 Answers

Front/rear? Wheel cylinder clip tool?

Posted on Nov 20, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where's is the fuse located for my brake lights on my 2007 Pontiac g6 and rear defrost fuse


Stop Lamps
your br
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery positive voltage to the stop lamps, transmission control module (TCM), engine control module (ECM), and stop lamp relay coil side. When the stop lamp relay receives battery voltage from the BCM, the relay coil is energized and the stop lamp relay switch contacts close applying battery voltage through the STOP LP fuse to illuminate the center high mounted stop lamp (CHMSL).
I'd say you have more then a bad fuse ,just reading how the brake lights function .You should have it hooked up to a professional grade scan tool ,one that can check for DTC'S - diagnostic trouble codes in the BCM - body control module !
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Brake Pedal Position Sensor parameter in the data list for the body control module (BCM).
  4. Apply and release the brake pedal.
Does the scan tool display a change in the voltage?

DTC B3903 Stop Lamp Relay Circuit DTC C0277 Brake Pedal Position Sensor Circuit
DTC C0278
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
Does the scan tool display DTC C0278 00?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections

3

Recalibrate the brake position sensor.

Circuit Description
DTC C0870
The body control module (BCM) applies a ground through the brake sensor reference low circuit to the brake pedal position (BPP) sensor. The BCM supplies a 5-volt reference through the brake sensor reference voltage circuit to the brake position sensor. When the brake pedal is being applied, the BPP sensor then sends a variable voltage signal through the brake sensor signal circuit to the BCM.
Circuit/System Verification
  1. Ignition ON, observe the scan tool Brake Lamp Cmd. parameter as you apply and unapply the brake pedal. The parameter should change between OFF and ON as the brake pedal is applied and released.
  2. ?‡'
    If the parameter does not change as the brake pedal is applied and released, refer to Brake Pedal Position Sensor (BPPS) Malfunction.

  3. With a scan tool, command the LR Stop/Turn Signal Lamp ON and OFF. The LR turn signal should turn ON and OFF when changing between the commanded states.
  4. ?‡'
    If the LR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.

  5. With a scan tool, command the RR Stop/Turn Signal Lamp ON and OFF. The RR turn signal should turn ON and OFF when changing between the commanded states.
?‡'
If the RR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.






I
I'd

Sep 26, 2015 | Pontiac Cars & Trucks

1 Answer

Adjust rear brakes on 2001 mazda tribute dx


Adjustments BRAKE SHOE ADJUSTMENT
  1. Remove the brake drum.

89219140


  1. Using the special tool, measure the inside diameter of the brake drum.

89219141


  1. Position the special tool on the brake shoes and linings and adjust accordingly.
  2. Install the brake drum.




Oct 07, 2011 | 2001 Mazda Tribute

1 Answer

98 corvette what is the proper procedure to bleeding the brakes


  1. Raise the vehicle on a suitable support.
  2. Remove all four tire and wheel assemblies.
  3. Inspect the brake system for leaks and visual damage.
  4. Inspect the battery state of charge.
  5. Install a scan tool.
  6. Turn ON the ignition, with the engine OFF. With the scan tool, establish communications with the electronic brake control module (EBCM). Select Special Functions. Select Automated Bleed from the Special Functions menu.
  7. Bleed the base brake system. Follow the scan tool directions until the desired brake pedal height is achieved.
  8. If the bleed procedure is aborted, a malfunction exists. Perform the following steps before resuming the bleed procedure:
    1. If a DTC is detected, check for the cause and repair as necessary.
    2. If the brake pedal feels spongy, perform the conventional brake bleed procedure again.

  9. When the desired pedal height is achieved, press the brake pedal in order to inspect for firmness. Remove the scan tool.
  10. Install the tire and wheel assemblies. Inspect the brake fluid level.
  11. Road test the vehicle while inspecting that the pedal remains high and firm.

  1. Raise the vehicle on a suitable support.
  2. Remove all four tire and wheel assemblies.
  3. Inspect the brake system for leaks and visual damage.
  4. Inspect the battery state of charge.
  5. Install a scan tool.
  6. Turn ON the ignition, with the engine OFF.
  7. With the scan tool, establish communications with the electronic brake control module (EBCM). Select Special Functions. Select Automated Bleed from the Special Functions menu.
  8. Bleed the base brake system.
  9. Follow the scan tool directions until the desired brake pedal height is achieved.

Jan 03, 2011 | 1998 Chevrolet Corvette

1 Answer

Need to replace the front & rear brakes . Is there any special tools needed to do this job .


For caliper brakes, mainly a large C-clamp or brake cylinder piston tool, to collapes the piston back into the caliper, to install the new pads. If you have rear drum brakes, they make a couple different brake spring tools for removing the springs on the brake shoes.

Nov 07, 2010 | 1994 Chevrolet Cavalier

1 Answer

What tools do I need to replace the brakes


To Replace Brake Pads...
Parts:
1. Brake Pad Set

Tools:
1. C-Clamp
2. Flat Head Screwdriver
3. Jack Stand Set
4. 3/8 in. Drive Ratchet
5. Combination Wrench Set
6. Tire Iron
7. Socket Set
8. 1/4 in. Drive Torque Wrench
9. Dial Indicator


To Replace Brake Shoes...
Parts:
1. Brake Shoe Set

Tools:
1. Combination Wrench Set
2. Floor Jack
3. Jack Stand Set
4. Mallet Hammer
5. Brake Spring Tool
6. Flat Head Screwdriver
7. Needle Nose Pliers
8. Tire Iron
9. Brake Resetting Gauge

Supplies:
1. Brake Cleaner


Hope this helped (remember comment and rated this).

May 05, 2010 | 2000 Dodge Stratus

1 Answer

Where can i find a manual on how to replace the brake line on a 02 chevy s10 xtreme?


I'm not aware of a particular Manual that specifically addresses Brake Line for your Specific Vehicle.
However I have replaced several "complete" and "partial" Brake Lines in my years of experience.
Specific/Pre-Contured Brake Lines for your Truck are available at most auto parts stores. Calt them for availability and prices.
However these are somewhat expensive. YOU CAN 'MAKE' YOUR OWN LINES!
Also available at these auto parts stores are two (2) tools you can buy.
1) A Brake Line Bending/Shaping Tool.
2) A Brake Line Cutting/Flaring Tool.
These tools are very easy (and fun) to use.
The auto parts stores carry "Straight" "Bulk" Brake Lines in different sizes (lenght and diameter). They also carry Brake Line "male" and "female" Brake Line Connectors. Make sure you purchase the correct diameter size Brake Line and the correct Connectors to fit these Brake Lines.
If the original Brake Line that you are replacing has viable (usable) sections and/or connectors you can use, then use them.
Take the old Brake Line off using a flare wrench.
Check your Brake Line Connectors to see if they will properly connect to your remain system.
Measure this piece with a material measuring tape (don't tell momma!). Measure the straight Brake Line and using the Brake Line Cutting Tool, cut the straight bulk Brake Line. Using the old Brake Line as a reference: use the Brake Line Bending Tool to shape the straight bulk Brake Line into the desired shape, matching as close as possible to the original Brake Line.
BEFORE USING THE BRAKE LINE FLARING TOOL:
Place the proper "male" or "female" connectors onto the line, FACING the proper directions.
Using the Brake Line Flaring Tool: Flare the ends of the Brake Line.
Connect the "new" Brake Line using the flare wrench.
Make sure you Bleed the entire Brake System.
Let me know if this helped, or if you have any additional information or questions. Feel free to contact me at FixYa.com!
ps: Make sure you clean, roll-up and put away that material measuring tape!!

Feb 12, 2010 | Chevrolet S 10 Cars & Trucks

3 Answers

How do you compress the caliper on a 2008 town & Country?


2008 Chrysler Town and Country
Replacing the Rear Brake Pads

Process is typical except for the rotating (screw type) brake piston. You cannot just compress the brake piston with a C-clamp, you have to turn the piston back in. This is easily done with the correct tool (Rear Disc Brake Piston Tool). The tool I had needed to be slightly modified to fit Chrysler's pattern.

Most Auto Parts store like Auto Zone and Parts Source will have the tools for lone or you can buy the tool and keep it in your tool box and the price ranges from $12.00 to $50.00 depending on the brake tool as to universal or specific to the vehicle make. Good luck and keep me posted.


Nov 08, 2009 | 2008 Chrysler Town & Country

1 Answer

Passat 2003 tdi, brake pad change..


Proper size wrenches and a large C-clamp to push piston back into the caliper is only tools for the front, but back disk brakes require special tool to TURN the piston as it is pushed back into caliper to reset emergency brake. This tool can often be borrowed from Auto parts store or purchased from Harbor Freight http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=40732 for about $20. Don't try to service rear disks without the tool, Calipers can be broken if not retracted properly!

Jul 03, 2009 | 1999 Volkswagen Passat

2 Answers

Is there any special tools to change the brakes on a 2000 lincoln ls


standard hand tools, remember to have the rotors turned by a machine shop.

May 26, 2009 | 2000 Lincoln LS

1 Answer

05 Equinox not able to remove right rear brake drum


Hiya...
Most rear brake-shoe design take some time to adjust than disc brakes...
If you have a special brake adjustment tool that your local automotive store sells, get this tool and pull out the rubber grommet plug, insert the brake adjustment tool until you 'feel' or hear the sound of 'skipping' on the brake self-adjuster spool inside as you wiggle /adjust the tool inside....(push it inside to get a firm feel that you can 'spin' it)
Try to push the tool downward or upward to check if that'll spin the brake self-adjuster part smaller to allow the brake shoes to 'shrink' which should allow you easy removal of the rear brake drum as you wiggle it out.

Be sure not to breathe in toxic brake dust upon successful brake drum removal.

Mar 28, 2009 | 2008 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...