Question about 2004 Chrysler Crossfire

1 Answer

Left front turn signal not working. bulb is good though

What could cause this?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

Check ground.

Posted on Nov 18, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Ford Edge Rear Left Turn Signal not working - Bulb and Socket confirmed good. Fuse Controlling both Left Front and Rear turn light confirmed good. Front Left turn light working fine.


The flasher is under the dash.If you turn on the signal listen for it's location.Turn on your 4 way flasher and see if the left rear light is flashing.If it's not then replace the bulb.If it still does'nt work after replacing the bulb check if there is power to the socket. Use a probe light.If no power to the socket.There is a break in the wire or worse the signal switch may be the culprit

Dec 18, 2017 | Ford Cars & Trucks

1 Answer

Left bleaker and break light not working. Turn signal works bleaks faster than right side.


Has the vehicle been in an accident on the left rear side. First check the bulb to be sure it is not defective, trade it out with the side that works properly to test. If the bulb works well then My thought are you may have a shorted wire. The turn signal flasher works by heat build up within the flasher the heat is caused by the load of the bulbs, the load heats the metal spring causing it to open the circuit then as quickly as it cools down the circuit closes again lighting the bulbs.
There is also a possibility of a defect in the turn signal mechanism on the steering column. The turn signal switch on many models does three different things on many models that use the same bulb element / or bulb for brake and turn on rear of vehicle. It controls the circuit for brake light by sending power both left and right side rear when turn signal is in neutral position then when turn signal is in left turn the switch cancels brake light power to left side rear and supplies flasher power to left side while maintaining brake light supply to the right side rear, and so on opposite when the right turn is chosen on turn signal switch. The turn signal indicators on the dash normally run off the same circuit as front turn signal bulb only which is also controlled by turn signal switch. Front has turn signals but no brake light.
I think there is an additional load on the left side rear turn circuit and it could be either a wire that is shorted or the turn signal switch if the same bulb element is used for both functions.
Often times if trailer lighting is connected the flasher will also blink a little faster because of the extra load of additional bulbs.

Feb 15, 2015 | Cars & Trucks

2 Answers

Front right and back right turn signal wont work but the front left and back left do


first check the bulbs on that side by visual or changing to the other side if you can't see that well if the bulbs from the front and back work or are good when checked the flasher has blown out on one side and you have to replace it other possible cause could be a broken wire for the right side lights so look at the connectors for that side front & back if all is good one more thing could do this the actual turn signal lever that you use to activate the signals could be bad for the right side especially if it does not go back to the normal position after making a turn and the steering wheel rotates back to it's normal position but the turn signal lever does not click back to the center position this would burn out that side from the signal constantly being on good luck stephen

Jan 03, 2015 | 1991 Ford Probe

2 Answers

69 turn signal problem left turn signal not working. right turn signal causes both to falsh


it's the grounds if they're both flashing fast it's definitely grounds take a test light and see if its got power goes through the test light grounded to the frame and if the light comes on then it's definitely your grounds

Jul 29, 2014 | 1969 Pontiac Firebird

1 Answer

What would cause 2004 thunderbird left rear turn signal to not work and bulb is o.k.


You need to check for power to rear light if none start to check wiring in reverse. Usually at turn signal switch or under drivers side carpet.

May 14, 2014 | 2004 Ford Thunderbird

1 Answer

1996 chevrolet C1500. The back left turning signal/brakes light is not working. Front left turning signal works fine.(Faster than usual). The bulb comes on when the headlights are on(steady), but does not...


The bulb for the turn signal/brake light is a double filament bulb. It will come on with the lights on, but should light the second filament, making it brighter, with the brakes applied or turn signal on. It could just be a bad bulb, but one common problem on these years of truck is the rear light circuit board and requires the whole assembly to be replaced. Start by checking the bulb first though.
Hope this helps. Good luck!

Apr 18, 2011 | Chevrolet C1500 Cars & Trucks

1 Answer

My left turning light gets stuck just stays on even though you turn left and go back but my right turning light works fine


The turn signals are designed to tell you when a bulb burns out. Turn your signal light on and walk around the vehicle to check if the outside signal lights are working. Sounds like you have both front and rear bulbs burnt out for the left.

Mar 10, 2011 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

My right turn signal doesn't work at all on my 1998 ford explorer


Have you checked the r/f turn signal socket? Corrosion can build up in the socket causing high resistance in the circuit, not illuminating the bulb. Back probe the wires for the connector and make sure you don't have power before digging deeper into diagnostics. If you have power, make sure the other wire has a good ground.

Jun 19, 2010 | 1998 Ford Explorer

1 Answer

Rear turn signal and hazard light don't flash (left side only)


The rear left turn signal bulb must be replaced immediatly before it melts the light socket, if it has'nt yet. Also please verify that the correct light bulb is being installed. because even though many bulbs look the same they are not identical. Installing the wrong bulb can be the begining of many, many problems in the particular circuit

Mar 26, 2010 | 2000 Ford Focus

1 Answer

Left turn signal quit working. 1969 chevy pickup-


sounds like you have a bad flasher which is usually located near the steering column under the dash. check for ground on front left bulb. may have to replace light socket if ground is good.please leave comment.

Mar 20, 2010 | 1983 Chevrolet K1500

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...