Question about 2000 Chevrolet Corvette
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
This light is usually caused by a problem in the ABS system. A problem in the ABS system will dissable the traction control system. you will need to have the computers scanned for trouble codes.
Posted on Jan 04, 2009
I have had exactly the same problem on and off for 3 years now - and just solved it last week thanks to another computer site. Remove and disassemble both grounds from the top of both the left and right frame rails adjacent to the front corners of the engine block. Completely clean the green corrosion from the internal parts with fine sandpaper and add dielectric grease then re-assemble. Clean the mounting bolt and frame hole while you're at it. Sounds time consuming and difficult, but it ain't. No more than 45 minutes combined. I am a technical airhead so if I can do it so can you. What clued me in was the problem always occurred around wet or humid weather. Also, the clock would always lose time overnite. That has ceased also. Good luck. Anyone know why my left headlite, when deployed, vibrates and shimmys??? Sully firstname.lastname@example.org
Posted on Jul 07, 2009
i have had this problem since about 6 months after i bought my 2001 impala. the problem is in the hubs. the wireing that runs throw them rubs together and eventually shorts the traction and abs. easy solution to fix it though. get into the hubs and wrap the wires. otherwise take the car in and explain the problem to them and exactly what you need done. 9-10 times they won't fix the problem unless you tell them what you want done. it is really simple and going to the dealer should only cost you about 100 to fix.
Posted on May 23, 2010
abs sensor is built into hub[bearing]common problem when changing them and or brakes r that the sensor connection is not properly reconnected or wire got damaged recheck the sensor wiring and that connector is connected to clip by strut clip is part of system
Posted on Jul 26, 2010
Traction control only works when one wheel is spinning faster than the other it trys to even them out so it wont spin...sometimes if one of the wheels come off the ground in an uneven area or if you take a turn too fast and one wheel turns when the other one dont it is designed to operate.
I would remove all wheels and check the braking system...Is it 4 wheel disc or rear drum ?
If it has rear drums you could have a wheel cylinder leak that will sometimes lock the wheel because of fluid contamination....This would cause both lights to come on...If you find no problems
sometimes the abs sensor builds up fragments on the magnet and makes the light come on...
or if the abs sensor is not close enough to the exciter ring it will make the light come on because it will be out of adjustment.....all you do is press the sensor inward until it barely touches the ring and it will adjust itself....You can sometimes clean the magnet if it is contaminated and make the light go off ( only after you reach 6 to 15 mph. it will go off ).If it dont go off you have to buy a sensor.
Also make sure all tires have same amount and plenty of air to keep vehicle in balance/level.
Posted on Feb 21, 2011
Tips for a great answer:
Feb 03, 2016 | 2001 Buick LeSabre
Jul 20, 2014 | 2001 Chevrolet Impala
Apr 08, 2014 | 2001 Cadillac Seville
Oct 04, 2012 | 2001 Oldsmobile Silhouette
Aug 06, 2011 | 1999 Chevrolet Corvette
Nov 07, 2009 | 2001 Hyundai Santa Fe
Oct 17, 2009 | 1993 Buick Park Avenue
Dec 09, 2008 | 2002 Chevrolet Impala
Jun 08, 2008 | 1999 Mazda Pickup
Jun 01, 2008 | 2001 Chevrolet Cavalier
76 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: